forked from jcrocholl/kossel
-
Notifications
You must be signed in to change notification settings - Fork 36
/
pg35l_extruder.scad
191 lines (175 loc) · 6.49 KB
/
pg35l_extruder.scad
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
// Based on MendelMax J-Head Micro-Extruder V5 by Ultibots:
// http://www.thingiverse.com/thing:42112
//
// Completely rewritten in OpenSCAD by Johann on 2013-01-19.
bearing_id = 3; // 623zz bearings are 3x10x4mm.
bearing_od = 10;
bearing_width = 4;
bearing_offset = 1.5;
body_height = 42;
body_width = 42; // V5: 52mm.
body_offset = 5; // V5: 7mm.
body_thickness = 21;
body_roundness = 10;
groovemount_od = 16.6; // 16mm nominal.
groovemount_height = 5; // Must push down on GrooveMount.
filament_offset = 1.5;
filament_dia = 1.75; // This is for 1.75mm filament.
filament_hole_dia = 2.5; // Size of opening into and out of the extruder.
filament_squish = 0.0; // Distance the drive gear teeth press into the filament.
// Measured drive gear sizes, sample size of one each (brandonheller):
// Trinity Labs hobbed pulley: 12.66mm od, 11mm valley od
// TriDPrinting hobbed pulley: 12.68mm od, 10.56mm valley od
// Make sure to set these, to reduce friction from twisting the filament, as well as ensure that the drive gear bearings actually rest against the drive gear.
drive_gear_width = 12;
drive_gear_id = 5;
drive_gear_od = 12.67;
drive_gear_valley_od = 11; // Diameter of drive gear at the valley of the teeth.
drive_gear_offset = drive_gear_valley_od/2+filament_dia/2-filament_squish; // Was: 7
cutout_id = 14.5;
cutout_height = 26;
funnel_depth = 7;
funnel_entrance_dia = 5;
foot_width = 62;
foot_offset = 0; // V5: 2mm but most GrooveMount plates are centered.
motor_mount_radius = 21;
motor_mount_angle = 54;
m3_radius = 1.8;
m3_nut_radius = 3.4;
m3_nut_height = 3;
m4_radius = 2.3;
m4_nut_radius = 4.5;
m4_nut_width = 7.5;
m4_nut_height = 4;
idler_x = -5.5;
idler_y = 10;
idler_z = 6.5;
// Place the two drive gear support bearings:
// - tangent to the drive gear
// - 90 degrees apart
// - 45 degrees rotated up or down from bottom of extruder.
bearing_drive_gear_offset = drive_gear_od/2+bearing_od/2;
bearing_drive_gear_offset_x_y = bearing_drive_gear_offset*(sqrt(2)/2);
bearing_x = bearing_drive_gear_offset_x_y+drive_gear_offset; // Was: 15.5
bearing_y = bearing_drive_gear_offset_x_y; // Was: 7.5
module pg35l_extruder() {
union() {
// Single wall support surfaces, to be removed after printing.
for (x = [-body_width/2, -body_width/3]) {
for (y = [-bearing_y, bearing_y]) {
translate([x-body_offset+0.6, y, bearing_offset])
cube([0.5, bearing_od, body_thickness*2/3], center=true);
}
}
intersection() {
translate([-drive_gear_offset, 0, 0]) difference() {
cylinder(r=cutout_id/2+0.6, h=body_thickness-2, center=true, $fn=60);
cylinder(r=cutout_id/2+0.3, h=body_thickness-1, center=true, $fn=60);
}
union() {
for (y = [-bearing_y, bearing_y]) {
translate([-bearing_x, y, bearing_offset]) {
cylinder(r=bearing_od/2+0.5, h=body_thickness/2, center=true);
// Drive gear support bearings
% cylinder(r=bearing_od/2, h=bearing_width, center=true);
}
}
}
}
// Bridge M3 screw holes above bearing spaces.
for (y = [-bearing_y, bearing_y]) {
translate([-bearing_x, y, bearing_offset+bearing_width/2+1.25]) {
cylinder(r=3, h=0.5, center=true);
}
}
difference() {
union() {
// Rounded top.
translate([-body_offset, -body_roundness, 0]) minkowski() {
cube([body_width-2*body_roundness, body_height, body_thickness-1],
center=true);
cylinder(r=body_roundness, h=1, center=true, $fn=60);
}
// Foot.
translate([-foot_offset, -body_height/2, 0])
cube([foot_width, 16, body_thickness], center=true);
}
// Uncomment the following line to look inside.
// translate([-30, 0, 16]) cube([60, 30, 30], center=true);
// Flat bottom.
translate([0, -body_height/2-20, 0])
cube([2*body_width, 40, body_thickness+1], center=true);
// Drive gear cutout.
translate([-drive_gear_offset, 0, 0]) {
cylinder(r=cutout_id/2, h=body_thickness+1, center=true, $fn=60);
translate([20, 0, 0])
cube([40, cutout_id, body_thickness+1], center=true);
}
// Idler cutout.
translate([25, 0, 0])
cube([40, cutout_height, body_thickness+1], center=true);
// Filament path and funnel.
translate([0, 0, filament_offset]) rotate([90, 0, 0]) {
// Filament cutout.
cylinder(r=filament_hole_dia/2, h=2*body_height, center=true, $fn=12);
// Filament funnel.
translate([0, 0, cutout_id/2])
cylinder(r1=funnel_entrance_dia, r2=filament_hole_dia/2, h=funnel_depth,
center=true, $fn=24);
}
// Motor mount screws.
translate([-drive_gear_offset, 0, 0])
for (x = [-motor_mount_radius, motor_mount_radius]) {
rotate([0, 0, motor_mount_angle])
translate([x, 0, body_thickness/2-m3_nut_height]) {
rotate([0, 0, -motor_mount_angle])
cylinder(r=m3_nut_radius, h=m3_nut_height*2, $fn=6);
translate([0, 0, 0.5]) rotate([180, 0, 0])
cylinder(r=m3_radius, h=body_thickness, $fn=12);
}
}
// Bearing spaces and mount screws.
for (y = [-bearing_y, bearing_y]) {
translate([-bearing_x, y, bearing_offset]) {
cylinder(r=(bearing_od+3)/2, h=bearing_width+2, center=true, $fn=32);
translate([-6.5, 0, 0])
cube([13, bearing_od+3, bearing_width+2], center=true);
}
translate([-bearing_x, y, m3_nut_height-body_thickness/2]) {
rotate([180, 0, 0])
cylinder(r=m3_nut_radius, h=m3_nut_height*2, $fn=6);
translate([0, 0, 0.5])
cylinder(r=m3_radius, h=body_thickness, $fn=12);
}
}
// Idler screws.
for (i = [-1, 1]) {
translate([0, i*idler_y, i*idler_z]) rotate([0, 90, 0]) {
cylinder(r=m3_radius, h=20, center=true, $fn=12);
for (x = [0, -3*i])
translate([x, 0, idler_x])
cylinder(r=m3_nut_radius, h=m3_nut_height, center=true, $fn=6);
}
}
// Foot mounting screws and nut pockets.
translate([-foot_offset, 5-body_height/2, filament_offset])
for (a = [0, 180]) {
rotate([-90, a, 0]) translate([25, 0, 0]) {
cylinder(r=m3_radius, h=13, center=true, $fn=12);
cylinder(r=m3_nut_radius, h=7, $fn=6);
}
}
// Groove mount.
translate([0, -body_height/2, filament_offset]) rotate([90, 0, 0])
cylinder(r=groovemount_od/2, h=2*groovemount_height, center=true);
}
}
// Drive gear.
% translate([-drive_gear_offset, 0, 0]) difference() {
cylinder(r=drive_gear_od/2, h=drive_gear_width, center=true);
cylinder(r=drive_gear_id/2, h=drive_gear_width+1, center=true, $fn=12);
}
}
translate([0, 0, body_thickness/2]) pg35l_extruder();
// Uncomment the following line for reference.
// translate([2, -21, 0]) % import("me_body_v5.1_3mm.stl");