diff --git a/hw/bsp/stm32f4/boards/stm32f407blackvet/STM32F407VETX_FLASH.ld b/hw/bsp/stm32f4/boards/stm32f407blackvet/STM32F407VETX_FLASH.ld
new file mode 100644
index 0000000000..6dec5543a9
--- /dev/null
+++ b/hw/bsp/stm32f4/boards/stm32f407blackvet/STM32F407VETX_FLASH.ld
@@ -0,0 +1,177 @@
+/**
+ ******************************************************************************
+ * @file LinkerScript.ld
+ * @author Auto-generated by STM32CubeIDE
+ * @brief Linker script for STM32F407VETx Device from STM32F4 series
+ * 512Kbytes FLASH
+ * 64Kbytes CCMRAM
+ * 128Kbytes RAM
+ *
+ * Set heap size, stack size and stack location according
+ * to application requirements.
+ *
+ * Set memory bank area and size if external memory is used
+ ******************************************************************************
+ * @attention
+ *
+ * © Copyright (c) 2020 STMicroelectronics.
+ * All rights reserved.
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200 ; /* required amount of heap */
+_Min_Stack_Size = 0x400 ; /* required amount of stack */
+
+/* Memories definition */
+MEMORY
+{
+ CCMRAM (xrw) : ORIGIN = 0x10000000, LENGTH = 64K
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K
+ FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 512K
+}
+
+/* Sections */
+SECTIONS
+{
+ /* The startup code into "FLASH" Rom type memory */
+ .isr_vector :
+ {
+ . = ALIGN(4);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(4);
+ } >FLASH
+
+ /* The program code and other data into "FLASH" Rom type memory */
+ .text :
+ {
+ . = ALIGN(4);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(4);
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data into "FLASH" Rom type memory */
+ .rodata :
+ {
+ . = ALIGN(4);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM.extab : {
+ . = ALIGN(4);
+ *(.ARM.extab* .gnu.linkonce.armextab.*)
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM : {
+ . = ALIGN(4);
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ . = ALIGN(4);
+ } >FLASH
+
+ .preinit_array :
+ {
+ . = ALIGN(4);
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ . = ALIGN(4);
+ } >FLASH
+
+ .init_array :
+ {
+ . = ALIGN(4);
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ . = ALIGN(4);
+ } >FLASH
+
+ .fini_array :
+ {
+ . = ALIGN(4);
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ . = ALIGN(4);
+ } >FLASH
+
+ /* Used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections into "RAM" Ram type memory */
+ .data :
+ {
+ . = ALIGN(4);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+
+ . = ALIGN(4);
+ _edata = .; /* define a global symbol at data end */
+
+ } >RAM AT> FLASH
+
+ /* Uninitialized data section into "RAM" Ram type memory */
+ . = ALIGN(4);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss section */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(4);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the compiler libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32f4/boards/stm32f407blackvet/board.cmake b/hw/bsp/stm32f4/boards/stm32f407blackvet/board.cmake
new file mode 100644
index 0000000000..52cf957004
--- /dev/null
+++ b/hw/bsp/stm32f4/boards/stm32f407blackvet/board.cmake
@@ -0,0 +1,18 @@
+set(MCU_VARIANT stm32f407xx)
+set(JLINK_DEVICE stm32f407ve)
+
+set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/STM32F407VETx_FLASH.ld)
+set(LD_FILE_IAR ${ST_CMSIS}/Source/Templates/iar/linker/${MCU_VARIANT}_flash.icf)
+
+set(STARTUP_FILE_GNU ${ST_CMSIS}/Source/Templates/gcc/startup_${MCU_VARIANT}.s)
+set(STARTUP_FILE_IAR ${ST_CMSIS}/Source/Templates/iar/startup_${MCU_VARIANT}.s)
+
+function(update_board TARGET)
+ target_compile_definitions(${TARGET} PUBLIC
+ STM32F407xx
+ HSE_VALUE=8000000
+ CORE_CM4
+ BOARD_TUD_RHPORT=0
+ BOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED
+ )
+endfunction()
diff --git a/hw/bsp/stm32f4/boards/stm32f407blackvet/board.h b/hw/bsp/stm32f4/boards/stm32f407blackvet/board.h
new file mode 100644
index 0000000000..b7a6d96c24
--- /dev/null
+++ b/hw/bsp/stm32f4/boards/stm32f407blackvet/board.h
@@ -0,0 +1,107 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2020, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+// LED
+#define LED_PORT GPIOA
+#define LED_PIN GPIO_PIN_6
+#define LED_STATE_ON 1
+
+// Button
+#define BUTTON_PORT GPIOE
+#define BUTTON_PIN GPIO_PIN_4
+#define BUTTON_STATE_ACTIVE 0
+
+// Enable PA2 as the debug log UART
+// It is not routed to the ST/Link on the Discovery board.
+#define UART_DEV USART2
+#define UART_GPIO_PORT GPIOA
+#define UART_GPIO_AF GPIO_AF7_USART2
+#define UART_TX_PIN GPIO_PIN_2
+#define UART_RX_PIN GPIO_PIN_3
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+static inline void board_clock_init(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* Enable Power Control clock */
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ /* Enable HSE Oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/2000000;
+ RCC_OscInitStruct.PLL.PLLN = 168;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+ RCC_OscInitStruct.PLL.PLLQ = 7;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2
+ clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
+
+ // Enable clocks for LED, Button, Uart
+ __HAL_RCC_GPIOA_CLK_ENABLE();
+ __HAL_RCC_GPIOE_CLK_ENABLE();
+ __HAL_RCC_GPIOH_CLK_ENABLE();
+ __HAL_RCC_USART2_CLK_ENABLE();
+}
+
+static inline void board_vbus_sense_init(void)
+{
+ // Black F407VET6 doesn't use VBUS sense (B device) explicitly disable it
+ USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_NOVBUSSENS;
+ USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_VBUSBSEN;
+ USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_VBUSASEN;
+}
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif /* BOARD_H_ */
diff --git a/hw/bsp/stm32f4/boards/stm32f407blackvet/board.mk b/hw/bsp/stm32f4/boards/stm32f407blackvet/board.mk
new file mode 100644
index 0000000000..a184804d3a
--- /dev/null
+++ b/hw/bsp/stm32f4/boards/stm32f407blackvet/board.mk
@@ -0,0 +1,16 @@
+CFLAGS += -DSTM32F407xx
+
+# GCC
+GCC_SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f407xx.s
+GCC_LD_FILE = $(BOARD_PATH)/STM32F407VGTx_FLASH.ld
+
+# IAR
+IAR_SRC_S += $(ST_CMSIS)/Source/Templates/iar/startup_stm32f407xx.s
+IAR_LD_FILE = $(ST_CMSIS)/Source/Templates/iar/linker/stm32f407xx_flash.icf
+
+
+# For flash-jlink target
+JLINK_DEVICE = stm32f407vg
+
+# flash target using on-board stlink
+flash: flash-stlink
diff --git a/hw/bsp/stm32f4/boards/stm32f407blackvet/stm32f4xx_hal_conf.h b/hw/bsp/stm32f4/boards/stm32f407blackvet/stm32f4xx_hal_conf.h
new file mode 100644
index 0000000000..e24e782eac
--- /dev/null
+++ b/hw/bsp/stm32f4/boards/stm32f407blackvet/stm32f4xx_hal_conf.h
@@ -0,0 +1,493 @@
+/**
+ ******************************************************************************
+ * @file stm32f4xx_hal_conf_template.h
+ * @author MCD Application Team
+ * @brief HAL configuration file
+ ******************************************************************************
+ * @attention
+ *
+ * © Copyright (c) 2017 STMicroelectronics.
+ * All rights reserved.
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F4xx_HAL_CONF_H
+#define __STM32F4xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+ * @brief This is the list of modules to be used in the HAL driver
+ */
+#define HAL_MODULE_ENABLED
+/* #define HAL_ADC_MODULE_ENABLED */
+/* #define HAL_CAN_MODULE_ENABLED */
+/* #define HAL_CAN_LEGACY_MODULE_ENABLED */
+/* #define HAL_CRC_MODULE_ENABLED */
+/* #define HAL_CEC_MODULE_ENABLED */
+/* #define HAL_CRYP_MODULE_ENABLED */
+/* #define HAL_DAC_MODULE_ENABLED */
+/* #define HAL_DCMI_MODULE_ENABLED */
+#define HAL_DMA_MODULE_ENABLED
+/* #define HAL_DMA2D_MODULE_ENABLED */
+/* #define HAL_ETH_MODULE_ENABLED */
+#define HAL_FLASH_MODULE_ENABLED
+/* #define HAL_NAND_MODULE_ENABLED */
+/* #define HAL_NOR_MODULE_ENABLED */
+/* #define HAL_PCCARD_MODULE_ENABLED */
+/* #define HAL_SRAM_MODULE_ENABLED */
+/* #define HAL_SDRAM_MODULE_ENABLED */
+/* #define HAL_HASH_MODULE_ENABLED */
+#define HAL_GPIO_MODULE_ENABLED
+/* #define HAL_EXTI_MODULE_ENABLED */
+/* #define HAL_I2C_MODULE_ENABLED */
+/* #define HAL_SMBUS_MODULE_ENABLED */
+/* #define HAL_I2S_MODULE_ENABLED */
+/* #define HAL_IWDG_MODULE_ENABLED */
+/* #define HAL_LTDC_MODULE_ENABLED */
+/* #define HAL_DSI_MODULE_ENABLED */
+#define HAL_PWR_MODULE_ENABLED
+/* #define HAL_QSPI_MODULE_ENABLED */
+#define HAL_RCC_MODULE_ENABLED
+/* #define HAL_RNG_MODULE_ENABLED */
+/* #define HAL_RTC_MODULE_ENABLED */
+/* #define HAL_SAI_MODULE_ENABLED */
+/* #define HAL_SD_MODULE_ENABLED */
+// #define HAL_SPI_MODULE_ENABLED
+/* #define HAL_TIM_MODULE_ENABLED */
+#define HAL_UART_MODULE_ENABLED
+/* #define HAL_USART_MODULE_ENABLED */
+/* #define HAL_IRDA_MODULE_ENABLED */
+/* #define HAL_SMARTCARD_MODULE_ENABLED */
+/* #define HAL_WWDG_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED
+/* #define HAL_PCD_MODULE_ENABLED */
+/* #define HAL_HCD_MODULE_ENABLED */
+/* #define HAL_FMPI2C_MODULE_ENABLED */
+/* #define HAL_SPDIFRX_MODULE_ENABLED */
+/* #define HAL_DFSDM_MODULE_ENABLED */
+/* #define HAL_LPTIM_MODULE_ENABLED */
+/* #define HAL_MMC_MODULE_ENABLED */
+
+/* ########################## HSE/HSI Values adaptation ##################### */
+/**
+ * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSE is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE (8000000U) /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT (100U) /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator (HSI) value.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSI is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE (16000000U) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE (32000U)
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+/**
+ * @brief External Low Speed oscillator (LSE) value.
+ */
+#if !defined (LSE_VALUE)
+ #define LSE_VALUE (32768U) /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+#if !defined (LSE_STARTUP_TIMEOUT)
+ #define LSE_STARTUP_TIMEOUT (5000U) /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief External clock source for I2S peripheral
+ * This value is used by the I2S HAL module to compute the I2S clock source
+ * frequency, this source is inserted directly through I2S_CKIN pad.
+ */
+#if !defined (EXTERNAL_CLOCK_VALUE)
+ #define EXTERNAL_CLOCK_VALUE (12288000U) /*!< Value of the External oscillator in Hz*/
+#endif /* EXTERNAL_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+ === you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+ * @brief This is the HAL system configuration section
+ */
+#define VDD_VALUE (3300U) /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY (0x0FU) /*!< tick interrupt priority */
+#define USE_RTOS 0U
+#define PREFETCH_ENABLE 1U
+#define INSTRUCTION_CACHE_ENABLE 1U
+#define DATA_CACHE_ENABLE 1U
+
+#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */
+#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */
+#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */
+#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */
+#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */
+#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */
+#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */
+#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */
+#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */
+#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */
+#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */
+#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */
+#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */
+#define USE_HAL_FMPI2C_REGISTER_CALLBACKS 0U /* FMPI2C register callback disabled */
+#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */
+#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */
+#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */
+#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */
+#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */
+#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */
+#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */
+#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */
+#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */
+#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */
+#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */
+#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */
+#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */
+#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */
+#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */
+#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */
+#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */
+#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */
+#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */
+#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
+#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
+#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */
+#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
+#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
+
+/* ########################## Assert Selection ############################## */
+/**
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * HAL drivers code
+ */
+/* #define USE_FULL_ASSERT 1U */
+
+/* ################## Ethernet peripheral configuration ##################### */
+
+/* Section 1 : Ethernet peripheral configuration */
+
+/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
+#define MAC_ADDR0 2U
+#define MAC_ADDR1 0U
+#define MAC_ADDR2 0U
+#define MAC_ADDR3 0U
+#define MAC_ADDR4 0U
+#define MAC_ADDR5 0U
+
+/* Definition of the Ethernet driver buffers size and count */
+#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
+#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
+#define ETH_RXBUFNB 4U /* 4 Rx buffers of size ETH_RX_BUF_SIZE */
+#define ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
+
+/* Section 2: PHY configuration section */
+
+/* DP83848 PHY Address*/
+#define DP83848_PHY_ADDRESS 0x01U
+/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
+#define PHY_RESET_DELAY 0x000000FFU
+/* PHY Configuration delay */
+#define PHY_CONFIG_DELAY 0x00000FFFU
+
+#define PHY_READ_TO 0x0000FFFFU
+#define PHY_WRITE_TO 0x0000FFFFU
+
+/* Section 3: Common PHY Registers */
+
+#define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */
+#define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */
+
+#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
+#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
+#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
+#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
+#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
+#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
+#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
+
+#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
+#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
+#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
+
+/* Section 4: Extended PHY Registers */
+
+#define PHY_SR ((uint16_t)0x0010) /*!< PHY status register Offset */
+#define PHY_MICR ((uint16_t)0x0011) /*!< MII Interrupt Control Register */
+#define PHY_MISR ((uint16_t)0x0012) /*!< MII Interrupt Status and Misc. Control Register */
+
+#define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */
+#define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */
+#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */
+
+#define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */
+#define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */
+
+#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */
+#define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */
+
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+
+#define USE_SPI_CRC 1U
+
+/* Includes ------------------------------------------------------------------*/
+/**
+ * @brief Include module's header file
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f4xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f4xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_EXTI_MODULE_ENABLED
+ #include "stm32f4xx_hal_exti.h"
+#endif /* HAL_EXTI_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+ #include "stm32f4xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f4xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f4xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f4xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
+ #include "stm32f4xx_hal_can_legacy.h"
+#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f4xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+ #include "stm32f4xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DMA2D_MODULE_ENABLED
+ #include "stm32f4xx_hal_dma2d.h"
+#endif /* HAL_DMA2D_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f4xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_DCMI_MODULE_ENABLED
+ #include "stm32f4xx_hal_dcmi.h"
+#endif /* HAL_DCMI_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+ #include "stm32f4xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f4xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+ #include "stm32f4xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+ #include "stm32f4xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+ #include "stm32f4xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_PCCARD_MODULE_ENABLED
+ #include "stm32f4xx_hal_pccard.h"
+#endif /* HAL_PCCARD_MODULE_ENABLED */
+
+#ifdef HAL_SDRAM_MODULE_ENABLED
+ #include "stm32f4xx_hal_sdram.h"
+#endif /* HAL_SDRAM_MODULE_ENABLED */
+
+#ifdef HAL_HASH_MODULE_ENABLED
+ #include "stm32f4xx_hal_hash.h"
+#endif /* HAL_HASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f4xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_SMBUS_MODULE_ENABLED
+ #include "stm32f4xx_hal_smbus.h"
+#endif /* HAL_SMBUS_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f4xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f4xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_LTDC_MODULE_ENABLED
+ #include "stm32f4xx_hal_ltdc.h"
+#endif /* HAL_LTDC_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f4xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+ #include "stm32f4xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f4xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SAI_MODULE_ENABLED
+ #include "stm32f4xx_hal_sai.h"
+#endif /* HAL_SAI_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32f4xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f4xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f4xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f4xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f4xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f4xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f4xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f4xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f4xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+ #include "stm32f4xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+#ifdef HAL_DSI_MODULE_ENABLED
+ #include "stm32f4xx_hal_dsi.h"
+#endif /* HAL_DSI_MODULE_ENABLED */
+
+#ifdef HAL_QSPI_MODULE_ENABLED
+ #include "stm32f4xx_hal_qspi.h"
+#endif /* HAL_QSPI_MODULE_ENABLED */
+
+#ifdef HAL_CEC_MODULE_ENABLED
+ #include "stm32f4xx_hal_cec.h"
+#endif /* HAL_CEC_MODULE_ENABLED */
+
+#ifdef HAL_FMPI2C_MODULE_ENABLED
+ #include "stm32f4xx_hal_fmpi2c.h"
+#endif /* HAL_FMPI2C_MODULE_ENABLED */
+
+#ifdef HAL_SPDIFRX_MODULE_ENABLED
+ #include "stm32f4xx_hal_spdifrx.h"
+#endif /* HAL_SPDIFRX_MODULE_ENABLED */
+
+#ifdef HAL_DFSDM_MODULE_ENABLED
+ #include "stm32f4xx_hal_dfsdm.h"
+#endif /* HAL_DFSDM_MODULE_ENABLED */
+
+#ifdef HAL_LPTIM_MODULE_ENABLED
+ #include "stm32f4xx_hal_lptim.h"
+#endif /* HAL_LPTIM_MODULE_ENABLED */
+
+#ifdef HAL_MMC_MODULE_ENABLED
+ #include "stm32f4xx_hal_mmc.h"
+#endif /* HAL_MMC_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr If expr is false, it calls assert_failed function
+ * which reports the name of the source file and the source
+ * line number of the call that failed.
+ * If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(uint8_t* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F4xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/hw/bsp/stm32f4/family.cmake b/hw/bsp/stm32f4/family.cmake
new file mode 100644
index 0000000000..7d9bbf3310
--- /dev/null
+++ b/hw/bsp/stm32f4/family.cmake
@@ -0,0 +1,134 @@
+include_guard()
+
+if (NOT BOARD)
+ message(FATAL_ERROR "BOARD not specified")
+endif ()
+
+set(ST_FAMILY f4)
+set(ST_PREFIX stm32${ST_FAMILY}xx)
+
+set(ST_HAL_DRIVER ${TOP}/hw/mcu/st/stm32${ST_FAMILY}xx_hal_driver)
+set(ST_CMSIS ${TOP}/hw/mcu/st/cmsis_device_${ST_FAMILY})
+set(CMSIS_5 ${TOP}/lib/CMSIS_5)
+
+# include board specific
+include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake)
+
+# toolchain set up
+set(CMAKE_SYSTEM_PROCESSOR cortex-m4 CACHE INTERNAL "System Processor")
+set(CMAKE_TOOLCHAIN_FILE ${TOP}/tools/cmake/toolchain/arm_${TOOLCHAIN}.cmake)
+
+set(FAMILY_MCUS STM32F4 CACHE INTERNAL "")
+
+# enable LTO if supported
+include(CheckIPOSupported)
+check_ipo_supported(RESULT IPO_SUPPORTED)
+if (IPO_SUPPORTED)
+ set(CMAKE_INTERPROCEDURAL_OPTIMIZATION TRUE)
+endif ()
+
+
+#------------------------------------
+# BOARD_TARGET
+#------------------------------------
+# only need to be built ONCE for all examples
+function(add_board_target BOARD_TARGET)
+ if (NOT TARGET ${BOARD_TARGET})
+ add_library(${BOARD_TARGET} STATIC
+ ${ST_CMSIS}/Source/Templates/system_${ST_PREFIX}.c
+ ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal.c
+ ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_cortex.c
+ ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_pwr_ex.c
+ ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_rcc.c
+ ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_rcc_ex.c
+ ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_dma.c
+ ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_gpio.c
+ ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_uart.c
+ ${STARTUP_FILE_${CMAKE_C_COMPILER_ID}}
+ )
+ target_include_directories(${BOARD_TARGET} PUBLIC
+ ${CMAKE_CURRENT_FUNCTION_LIST_DIR}
+ ${CMSIS_5}/CMSIS/Core/Include
+ ${ST_CMSIS}/Include
+ ${ST_HAL_DRIVER}/Inc
+ )
+ target_compile_options(${BOARD_TARGET} PUBLIC
+ )
+ target_compile_definitions(${BOARD_TARGET} PUBLIC
+ )
+
+ update_board(${BOARD_TARGET})
+
+ if (CMAKE_C_COMPILER_ID STREQUAL "GNU")
+ target_link_options(${BOARD_TARGET} PUBLIC
+ "LINKER:--script=${LD_FILE_GNU}"
+ -nostartfiles
+ # nanolib
+ --specs=nosys.specs
+ --specs=nano.specs
+ )
+ elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR")
+ target_link_options(${BOARD_TARGET} PUBLIC
+ "LINKER:--config=${LD_FILE_IAR}"
+ )
+ endif ()
+ endif ()
+endfunction()
+
+
+#------------------------------------
+# Functions
+#------------------------------------
+function(family_configure_example TARGET)
+ family_configure_common(${TARGET})
+
+ # Board target
+ add_board_target(board_${BOARD})
+
+ #---------- Port Specific ----------
+ # These files are built for each example since it depends on example's tusb_config.h
+ target_sources(${TARGET} PUBLIC
+ # BSP
+ ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c
+ ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c
+ )
+ target_include_directories(${TARGET} PUBLIC
+ # family, hw, board
+ ${CMAKE_CURRENT_FUNCTION_LIST_DIR}
+ ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../
+ ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD}
+ )
+
+ # Add TinyUSB target and port source
+ family_add_tinyusb(${TARGET} OPT_MCU_STM32F4)
+ if (MCU_VARIANT STREQUAL "stm32f407xx")
+ target_sources(${TARGET}-tinyusb PUBLIC
+ ${TOP}/src/portable/synopsys/dwc2/dcd_dwc2.c
+ )
+ else()
+ target_sources(${TARGET}-tinyusb PUBLIC
+ ${TOP}/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c
+ )
+ endif()
+ target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD})
+
+ # Link dependencies
+ target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb)
+
+ # Flashing
+ family_flash_stlink(${TARGET})
+ family_flash_jlink(${TARGET})
+endfunction()
+
+
+function(family_configure_device_example TARGET)
+ family_configure_example(${TARGET})
+endfunction()
+
+function(family_configure_host_example TARGET)
+ family_configure_example(${TARGET})
+endfunction()
+
+function(family_configure_dual_usb_example TARGET)
+ family_configure_example(${TARGET})
+endfunction()
diff --git a/hw/bsp/stm32f4/stm32f4xx_hal_conf.h b/hw/bsp/stm32f4/stm32f4xx_hal_conf.h
new file mode 100644
index 0000000000..e24e782eac
--- /dev/null
+++ b/hw/bsp/stm32f4/stm32f4xx_hal_conf.h
@@ -0,0 +1,493 @@
+/**
+ ******************************************************************************
+ * @file stm32f4xx_hal_conf_template.h
+ * @author MCD Application Team
+ * @brief HAL configuration file
+ ******************************************************************************
+ * @attention
+ *
+ * © Copyright (c) 2017 STMicroelectronics.
+ * All rights reserved.
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F4xx_HAL_CONF_H
+#define __STM32F4xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+ * @brief This is the list of modules to be used in the HAL driver
+ */
+#define HAL_MODULE_ENABLED
+/* #define HAL_ADC_MODULE_ENABLED */
+/* #define HAL_CAN_MODULE_ENABLED */
+/* #define HAL_CAN_LEGACY_MODULE_ENABLED */
+/* #define HAL_CRC_MODULE_ENABLED */
+/* #define HAL_CEC_MODULE_ENABLED */
+/* #define HAL_CRYP_MODULE_ENABLED */
+/* #define HAL_DAC_MODULE_ENABLED */
+/* #define HAL_DCMI_MODULE_ENABLED */
+#define HAL_DMA_MODULE_ENABLED
+/* #define HAL_DMA2D_MODULE_ENABLED */
+/* #define HAL_ETH_MODULE_ENABLED */
+#define HAL_FLASH_MODULE_ENABLED
+/* #define HAL_NAND_MODULE_ENABLED */
+/* #define HAL_NOR_MODULE_ENABLED */
+/* #define HAL_PCCARD_MODULE_ENABLED */
+/* #define HAL_SRAM_MODULE_ENABLED */
+/* #define HAL_SDRAM_MODULE_ENABLED */
+/* #define HAL_HASH_MODULE_ENABLED */
+#define HAL_GPIO_MODULE_ENABLED
+/* #define HAL_EXTI_MODULE_ENABLED */
+/* #define HAL_I2C_MODULE_ENABLED */
+/* #define HAL_SMBUS_MODULE_ENABLED */
+/* #define HAL_I2S_MODULE_ENABLED */
+/* #define HAL_IWDG_MODULE_ENABLED */
+/* #define HAL_LTDC_MODULE_ENABLED */
+/* #define HAL_DSI_MODULE_ENABLED */
+#define HAL_PWR_MODULE_ENABLED
+/* #define HAL_QSPI_MODULE_ENABLED */
+#define HAL_RCC_MODULE_ENABLED
+/* #define HAL_RNG_MODULE_ENABLED */
+/* #define HAL_RTC_MODULE_ENABLED */
+/* #define HAL_SAI_MODULE_ENABLED */
+/* #define HAL_SD_MODULE_ENABLED */
+// #define HAL_SPI_MODULE_ENABLED
+/* #define HAL_TIM_MODULE_ENABLED */
+#define HAL_UART_MODULE_ENABLED
+/* #define HAL_USART_MODULE_ENABLED */
+/* #define HAL_IRDA_MODULE_ENABLED */
+/* #define HAL_SMARTCARD_MODULE_ENABLED */
+/* #define HAL_WWDG_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED
+/* #define HAL_PCD_MODULE_ENABLED */
+/* #define HAL_HCD_MODULE_ENABLED */
+/* #define HAL_FMPI2C_MODULE_ENABLED */
+/* #define HAL_SPDIFRX_MODULE_ENABLED */
+/* #define HAL_DFSDM_MODULE_ENABLED */
+/* #define HAL_LPTIM_MODULE_ENABLED */
+/* #define HAL_MMC_MODULE_ENABLED */
+
+/* ########################## HSE/HSI Values adaptation ##################### */
+/**
+ * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSE is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE (8000000U) /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT (100U) /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator (HSI) value.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSI is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE (16000000U) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE (32000U)
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+/**
+ * @brief External Low Speed oscillator (LSE) value.
+ */
+#if !defined (LSE_VALUE)
+ #define LSE_VALUE (32768U) /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+#if !defined (LSE_STARTUP_TIMEOUT)
+ #define LSE_STARTUP_TIMEOUT (5000U) /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief External clock source for I2S peripheral
+ * This value is used by the I2S HAL module to compute the I2S clock source
+ * frequency, this source is inserted directly through I2S_CKIN pad.
+ */
+#if !defined (EXTERNAL_CLOCK_VALUE)
+ #define EXTERNAL_CLOCK_VALUE (12288000U) /*!< Value of the External oscillator in Hz*/
+#endif /* EXTERNAL_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+ === you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+ * @brief This is the HAL system configuration section
+ */
+#define VDD_VALUE (3300U) /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY (0x0FU) /*!< tick interrupt priority */
+#define USE_RTOS 0U
+#define PREFETCH_ENABLE 1U
+#define INSTRUCTION_CACHE_ENABLE 1U
+#define DATA_CACHE_ENABLE 1U
+
+#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */
+#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */
+#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */
+#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */
+#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */
+#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */
+#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */
+#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */
+#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */
+#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */
+#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */
+#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */
+#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */
+#define USE_HAL_FMPI2C_REGISTER_CALLBACKS 0U /* FMPI2C register callback disabled */
+#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */
+#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */
+#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */
+#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */
+#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */
+#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */
+#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */
+#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */
+#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */
+#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */
+#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */
+#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */
+#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */
+#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */
+#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */
+#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */
+#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */
+#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */
+#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */
+#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
+#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
+#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */
+#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
+#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
+
+/* ########################## Assert Selection ############################## */
+/**
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * HAL drivers code
+ */
+/* #define USE_FULL_ASSERT 1U */
+
+/* ################## Ethernet peripheral configuration ##################### */
+
+/* Section 1 : Ethernet peripheral configuration */
+
+/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
+#define MAC_ADDR0 2U
+#define MAC_ADDR1 0U
+#define MAC_ADDR2 0U
+#define MAC_ADDR3 0U
+#define MAC_ADDR4 0U
+#define MAC_ADDR5 0U
+
+/* Definition of the Ethernet driver buffers size and count */
+#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
+#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
+#define ETH_RXBUFNB 4U /* 4 Rx buffers of size ETH_RX_BUF_SIZE */
+#define ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
+
+/* Section 2: PHY configuration section */
+
+/* DP83848 PHY Address*/
+#define DP83848_PHY_ADDRESS 0x01U
+/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
+#define PHY_RESET_DELAY 0x000000FFU
+/* PHY Configuration delay */
+#define PHY_CONFIG_DELAY 0x00000FFFU
+
+#define PHY_READ_TO 0x0000FFFFU
+#define PHY_WRITE_TO 0x0000FFFFU
+
+/* Section 3: Common PHY Registers */
+
+#define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */
+#define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */
+
+#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
+#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
+#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
+#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
+#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
+#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
+#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
+
+#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
+#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
+#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
+
+/* Section 4: Extended PHY Registers */
+
+#define PHY_SR ((uint16_t)0x0010) /*!< PHY status register Offset */
+#define PHY_MICR ((uint16_t)0x0011) /*!< MII Interrupt Control Register */
+#define PHY_MISR ((uint16_t)0x0012) /*!< MII Interrupt Status and Misc. Control Register */
+
+#define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */
+#define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */
+#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */
+
+#define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */
+#define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */
+
+#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */
+#define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */
+
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+
+#define USE_SPI_CRC 1U
+
+/* Includes ------------------------------------------------------------------*/
+/**
+ * @brief Include module's header file
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f4xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f4xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_EXTI_MODULE_ENABLED
+ #include "stm32f4xx_hal_exti.h"
+#endif /* HAL_EXTI_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+ #include "stm32f4xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f4xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f4xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f4xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
+ #include "stm32f4xx_hal_can_legacy.h"
+#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f4xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+ #include "stm32f4xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DMA2D_MODULE_ENABLED
+ #include "stm32f4xx_hal_dma2d.h"
+#endif /* HAL_DMA2D_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f4xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_DCMI_MODULE_ENABLED
+ #include "stm32f4xx_hal_dcmi.h"
+#endif /* HAL_DCMI_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+ #include "stm32f4xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f4xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+ #include "stm32f4xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+ #include "stm32f4xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+ #include "stm32f4xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_PCCARD_MODULE_ENABLED
+ #include "stm32f4xx_hal_pccard.h"
+#endif /* HAL_PCCARD_MODULE_ENABLED */
+
+#ifdef HAL_SDRAM_MODULE_ENABLED
+ #include "stm32f4xx_hal_sdram.h"
+#endif /* HAL_SDRAM_MODULE_ENABLED */
+
+#ifdef HAL_HASH_MODULE_ENABLED
+ #include "stm32f4xx_hal_hash.h"
+#endif /* HAL_HASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f4xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_SMBUS_MODULE_ENABLED
+ #include "stm32f4xx_hal_smbus.h"
+#endif /* HAL_SMBUS_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f4xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f4xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_LTDC_MODULE_ENABLED
+ #include "stm32f4xx_hal_ltdc.h"
+#endif /* HAL_LTDC_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f4xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+ #include "stm32f4xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f4xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SAI_MODULE_ENABLED
+ #include "stm32f4xx_hal_sai.h"
+#endif /* HAL_SAI_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32f4xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f4xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f4xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f4xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f4xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f4xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f4xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f4xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f4xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+ #include "stm32f4xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+#ifdef HAL_DSI_MODULE_ENABLED
+ #include "stm32f4xx_hal_dsi.h"
+#endif /* HAL_DSI_MODULE_ENABLED */
+
+#ifdef HAL_QSPI_MODULE_ENABLED
+ #include "stm32f4xx_hal_qspi.h"
+#endif /* HAL_QSPI_MODULE_ENABLED */
+
+#ifdef HAL_CEC_MODULE_ENABLED
+ #include "stm32f4xx_hal_cec.h"
+#endif /* HAL_CEC_MODULE_ENABLED */
+
+#ifdef HAL_FMPI2C_MODULE_ENABLED
+ #include "stm32f4xx_hal_fmpi2c.h"
+#endif /* HAL_FMPI2C_MODULE_ENABLED */
+
+#ifdef HAL_SPDIFRX_MODULE_ENABLED
+ #include "stm32f4xx_hal_spdifrx.h"
+#endif /* HAL_SPDIFRX_MODULE_ENABLED */
+
+#ifdef HAL_DFSDM_MODULE_ENABLED
+ #include "stm32f4xx_hal_dfsdm.h"
+#endif /* HAL_DFSDM_MODULE_ENABLED */
+
+#ifdef HAL_LPTIM_MODULE_ENABLED
+ #include "stm32f4xx_hal_lptim.h"
+#endif /* HAL_LPTIM_MODULE_ENABLED */
+
+#ifdef HAL_MMC_MODULE_ENABLED
+ #include "stm32f4xx_hal_mmc.h"
+#endif /* HAL_MMC_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr If expr is false, it calls assert_failed function
+ * which reports the name of the source file and the source
+ * line number of the call that failed.
+ * If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(uint8_t* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F4xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/