Welcome to esp32Micronet Discussions! #3
Replies: 11 comments 2 replies
-
|
hello great job i am trying to compile the code but my arduino ide gives me a bad card error i don't know if this is the code what setting do you use for an esp32 wroom thank you very much i will cross the atlantic at the end of the month i would tell you if it worked permanently have a nice day |
Beta Was this translation helpful? Give feedback.
-
|
I believed I used the "ESP32 Dev Module" board but can't check right now. AFAIK it should compile under any esp32 board profile. Can you paste your build log here? |
Beta Was this translation helpful? Give feedback.
-
|
Ok i m sailong now but i make thos thanks
Le jeu. 10 nov. 2022 à 16:11, mnsnoop ***@***.***> a écrit :
… I believed I used the "ESP32 Dev Module" board but can't check right now.
AFAIK it should compile under any esp32 board profile. Can you paste your
build log here?
—
Reply to this email directly, view it on GitHub
<#3 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AOSIXEUL3CZ3SDYNJ2Z7W6TWHUUFXANCNFSM5WACIJBA>
.
You are receiving this because you commented.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
Sorry i look my build log hihi one ligne is not visible in the windows i copy one librairie out off his folder now everything is good thanks a lot i receive the material in one week and big test throught the atlantic for the n2k bridge if it work well my pilot have wind thanks a lot |
Beta Was this translation helpful? Give feedback.
-
|
Good to hear, enjoy your sail. |
Beta Was this translation helpful? Give feedback.
-
|
good evening I have a problem with my wind transducer I have a race master as a screen and just an anemometer I can't manage to pair them I succeeded twice when I replaced the battery then nothing unfortunately I couldn't solder the cc1001 my soldering iron is too big being in cape verde i can't order another cc1001 is there a way to check that the t120 is emitting? if you have a test technique to confirm a failure I have an rtl sdr |
Beta Was this translation helpful? Give feedback.
-
|
When you first turn on a display after a short 2 to 4 second period it will transmit continuously for 4 to 6 seconds. That's the easiest way to catch it transmitting. If you put the display close enough to the sdr antenna and turn the gain up you should be able to see and hear it transmit every second. These transmissions are short but should show up. |
Beta Was this translation helpful? Give feedback.
-
|
hello this is for the screen do you know if the anemometer emits
permanently or if it goes to sleep? I saw the signals pass during the
pairing but when I listen to my anemometer I still don't see any signals
thank you for taking the time to answer me I tried to change the frequency
but still nothing I will charge it fully in the sun but the pole eats at
2.9 v I think that's enough? have a good day
Le jeu. 24 nov. 2022 à 13:51, mnsnoop ***@***.***> a écrit :
… When you first turn on a display after a short 2 to 4 second period it
will transmit continuously for 4 to 6 seconds. That's the easiest way to
catch it transmitting. If you put the display close enough to the sdr
antenna and turn the gain up you should be able to see and hear it transmit
every second. These transmissions are short but should show up.
—
Reply to this email directly, view it on GitHub
<#3 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AOSIXEQGAK2KZ3FFJKNM23TWJ56GLANCNFSM5WACIJBA>
.
You are receiving this because you commented.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
It goes to sleep. The anemometer will only transmit when asked by another device. 2.9v is enough for it to function. |
Beta Was this translation helpful? Give feedback.
-
|
Ok thanks i think it is sleep and the race master don t wake up it or is
dead 😖
Le jeu. 24 nov. 2022 à 14:51, mnsnoop ***@***.***> a écrit :
… It goes to sleep. The anemometer will only transmit when asked by another
device. 2.9v is enough for it to function.
—
Reply to this email directly, view it on GitHub
<#3 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AOSIXEXNZ4ILAV57Y6HWKEDWJ6FGPANCNFSM5WACIJBA>
.
You are receiving this because you commented.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
The 4 to 6 second continuous transmission when a display is turned on is the wake up signal. If the display is sending that signal out then the issue is with the anemometer or pairing of the two. |
Beta Was this translation helpful? Give feedback.
-
|
Ok thanks maybe is paired whith another device but i don t know how to
reset the anemometer thanks a lot now sailing throught the atlantic i see
that later no wind sensor all right
***@***.***/ my boat homemade building
Le jeu. 24 nov. 2022 à 15:06, mnsnoop ***@***.***> a écrit :
… The 4 to 6 second continuous transmission when a display is turned on is
the wake up signal. If the display is sending that signal out then the
issue is with the anemometer or pairing of the two.
—
Reply to this email directly, view it on GitHub
<#3 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AOSIXEWPILZ5UEQLQ4N2TJTWJ6G7FANCNFSM5WACIJBA>
.
You are receiving this because you commented.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
There is no reset. It will pair with any display that is close enough. Happy sailing! |
Beta Was this translation helpful? Give feedback.
-
👋 Welcome!
We’re using Discussions as a place to connect with other members of our community. We hope that you:
build together 💪.
To get started, comment below with an introduction of yourself and tell us about what you do with this community.
Beta Was this translation helpful? Give feedback.
All reactions