diff --git a/docs/feeder-connection-kit/accessories/index.md b/docs/feeder-connection-kit/accessories/index.md index ad7116d..13fdd6c 100644 --- a/docs/feeder-connection-kit/accessories/index.md +++ b/docs/feeder-connection-kit/accessories/index.md @@ -28,28 +28,28 @@ This section will guide the reader on how to properly prepare the accessories th ![](img/IMG_3669.png) -## feeder-blade-cable-harness +## feeder-blade-harness-set ###Cutting up feeder-slot-cable-harness * Begin by unpacking a stock `feeder-slot-cable-harness` ![](img/feeder-blade-cable-harness-rework1.jpg) -* Unroll the harness and cut the cable after Slot #1 connector to create `mobo-to-slot1-cable-harness` before setting it aside for later use +* Unroll the harness and cut the cable after Slot #1 connector to create `mobo-to-slot1-harness` before setting it aside for later use ![](img/feeder-blade-cable-harness-rework2.jpg) * Cut the loose cable leading up to the Slot #2 IDC connector ![](img/feeder-blade-cable-harness-rework3.jpg) -* Cut out the center of the cable between Slot #25 and #26 as shown below to create `slot25-to-slot26-cable-harness` before setting it aside for later use +* Cut out the center of the cable between Slot #25 and #26 as shown below to create `slot25-to-slot26-harness` before setting it aside for later use ![](img/feeder-blade-cable-harness-rework4.jpg) ![](img/feeder-blade-cable-harness-rework5.jpg) ![](img/feeder-blade-cable-harness-rework6.jpg) ![](img/feeder-blade-cable-harness-rework7.jpg) -* Segment the remaining `feeder-slot-cable-harness` into 30mm long cables with a connector at each end to create 23x `blade12-to-blade13-cable-harness` before setting them aside for later use +* Segment the remaining `feeder-slot-cable-harness` into 30mm long cables with a connector at each end to create 23x `blade-jumper-harness` before setting them aside for later use ![](img/feeder-blade-cable-harness-rework8.jpg) ![](img/feeder-blade-cable-harness-rework10.jpg) -###Packaging feeder-blade-cable-harness +###Packaging feeder-blade-harness-set * Collect the following cables and package them into a `4x6-anti-static-bag` before sealing it shut - * 1x `mobo-to-slot1-cable-harness` - * 1x `slot25-to-slot26-cable-harness` - * 2x `blade12-to-blade13-cable-harness` + * 1x `mobo-to-slot1-harness` + * 1x `slot25-to-slot26-harness` + * 2x `blade-jumper-harness` ![](img/feeder-blade-cable-harness-rework11.jpg) ![](img/feeder-blade-cable-harness-rework12.jpg) @@ -58,8 +58,8 @@ This section will guide the reader on how to properly prepare the accessories th ###Additional notes * To keep the workstation organized keep everything organized in the bin shown below: * Section #1 - unmodified `feeder-slot-cable-harness` pieces - * Section #2 - spare `blade12-to-blade13-cable-harness` pieces - * Section #3 - finished and bagged`feeder-blade-cable-harness` units + * Section #2 - spare `blade-jumper-harness` pieces + * Section #3 - finished and bagged`feeder-blade-harness-set` units ![](img/feeder-blade-cable-harness-rework14.jpg) !!!success "These three assemblies can now be set aside for further use in packout" \ No newline at end of file diff --git a/docs/feeder-connection-kit/slot-set/img/slot-set-1.JPG b/docs/feeder-connection-kit/slot-set/img/slot-set-1.JPG deleted file mode 100644 index 0b1dc55..0000000 --- a/docs/feeder-connection-kit/slot-set/img/slot-set-1.JPG +++ /dev/null @@ -1,3 +0,0 @@ -version https://git-lfs.github.com/spec/v1 -oid sha256:602f97ccdaeb193f7e73a4d6b4dc9389d5b29ba4d3ea9a0abccfa160d7c93456 -size 1475890 diff --git a/docs/feeder-connection-kit/slot-set/img/slot-set-12.JPG b/docs/feeder-connection-kit/slot-set/img/slot-set-12.JPG deleted file mode 100644 index 8eec073..0000000 Binary files a/docs/feeder-connection-kit/slot-set/img/slot-set-12.JPG and /dev/null differ diff --git a/docs/feeder-connection-kit/slot-set/img/slot-set-15.JPG b/docs/feeder-connection-kit/slot-set/img/slot-set-15.JPG deleted file mode 100644 index c79a3c1..0000000 Binary files a/docs/feeder-connection-kit/slot-set/img/slot-set-15.JPG and /dev/null differ diff --git a/docs/feeder-connection-kit/slot-set/img/slot-set-2.JPG b/docs/feeder-connection-kit/slot-set/img/slot-set-2.JPG deleted file mode 100644 index 0e570ba..0000000 Binary files a/docs/feeder-connection-kit/slot-set/img/slot-set-2.JPG and /dev/null differ diff --git a/docs/index.md b/docs/index.md index 1db6b66..a56ef8f 100644 --- a/docs/index.md +++ b/docs/index.md @@ -13,7 +13,7 @@ Open Hardware Assembly Instructions for products made by Opulo Inc. | | | | |:-------------------------:|:-------------------------:|:-------------------------:| -|
LumenPnP v3.1 |
8mm Feeder|
Feeder Connection Kit| +|
LumenPnP |
8mm Feeder|
Feeder Connection Kit| |
Pump and Valve Kit |
Toolhead Kit|
Nozzle Tip Set| |
PCB Kit |
Feeder Part Kit|
Staging Plate Set | |
Strip Feeder|
Placeholder 2|
Placeholder 3| diff --git a/docs/lumen/additional-parts/index.md b/docs/lumen/additional-parts/index.md index a33a6be..f24b76c 100644 --- a/docs/lumen/additional-parts/index.md +++ b/docs/lumen/additional-parts/index.md @@ -69,3 +69,6 @@ These parts and their respective quantities are as follows: ![](img/build-foot-rubber.jpeg) - Place each `static-camera-foot` into a yellow NEEDS QC bin while it awaits inspection ![](img/aux-staging-plate-foot.png) + +### feeder-blade-harness-set +- Prepare this item by following [these instructions](/feeder-connection-kit/accessories/#feeder-blade-cable-harness) \ No newline at end of file diff --git a/docs/lumen/feeder-rail/index.md b/docs/lumen/feeder-rail/index.md index 097d8d1..b6876fe 100644 --- a/docs/lumen/feeder-rail/index.md +++ b/docs/lumen/feeder-rail/index.md @@ -1,8 +1,10 @@ -#Front-feeder-rail / Rear-feeder-rail - +#Feeder Rail (Front and Rear) ## Introduction The purpose of these work instructions is to cover the assembly process for the LumenPnP's front and rear feeder rail. These rails are used by the LumenPnP to space its two y-gantry assemblies apart. These rails also allow for auto feeders to be installed onto the LumenPnP and electronically connected via the 50x mounted feeder slots. +!!!warning "This set of work instructions is out of date" + This document shows how to assemble feeder rails with Individual Feeder Slots rather than the Feeder Blades we now use as of the LumenPnP v3.2 release. Please consult a teamamte if you are not verbally trained on what to do differently." + Before: diff --git a/docs/lumen/index.md b/docs/lumen/index.md index 1639152..48233e8 100644 --- a/docs/lumen/index.md +++ b/docs/lumen/index.md @@ -1,7 +1,7 @@ -# Work Instructions for LumenPnP V3.1 +# Work Instructions for LumenPnP V3.2 ## Purpose -The goal of this work instruction is to walk document Opulo's assembly process for a LumenPnP V3.1 all the way through final pack out. +The goal of this work instruction is to walk document Opulo's assembly process for a LumenPnP V3.2 all the way through final pack out. ## Next Steps To proceed through these instructions, click the **Next** button found on the bottom footer of most pages. diff --git a/docs/lumen/pack-out/index.md b/docs/lumen/pack-out/index.md index 09d8aed..e9301ad 100644 --- a/docs/lumen/pack-out/index.md +++ b/docs/lumen/pack-out/index.md @@ -8,7 +8,7 @@ * `x-gantry` * `getting-started-kit` * `Tool-kit` - * `feeder-slot-cable-harness` + * `feeder-blade-harness-set` * 2x `front-leg-extension` * 2x `back-leg-extension` @@ -143,10 +143,13 @@ ![](img/frontlegextension.jpg) -### Packaging `feeder-slot-cable-harness` -1. Insert `feeder-slot-cable-harness` into the tray in the region shown below +### Packaging `feeder-blade-harness-set` +1. Insert `feeder-blade-harness-set` into the tray in the region shown below ![](img/slotcable.jpg) + + !!!warning "This photo is out of date" + Be sure to use the new version of this cable, `feeder-blade-harness-set`, rather than the earlier version shown above. ### Confirm the contents of `lower-foam-tray` Confirm the `lower-foam-tray` matches the image shown below before continuing: @@ -398,4 +401,4 @@ Confirm the `lower-foam-tray` matches the image shown below before continuing: ![](img/QC-Form/8-qc-form.jpeg) -!!!success "The LumenPnP should now be ready for fulfillment!" \ No newline at end of file +!!!success "The LumenPnP should now be ready for fulfillment!" diff --git a/docs/lumen/y-gantry/index.md b/docs/lumen/y-gantry/index.md index 5bbf9c5..af59a30 100644 --- a/docs/lumen/y-gantry/index.md +++ b/docs/lumen/y-gantry/index.md @@ -1,5 +1,5 @@ ## Intro -The purpose of this work instruction is to explain the assembly process for the LumenPnP v3.1.0 Left-Side Y-Gantry (`y-gantry-left`). +The purpose of this work instruction is to explain the assembly process for the LumenPnP v3.2.0 Left-Side Y-Gantry (`y-gantry-left`). ## Create Y-Gantry Subassembly - Remove any stringing from the print with a heat gun diff --git a/mkdocs.yml b/mkdocs.yml index b2de377..8c70a4b 100644 --- a/mkdocs.yml +++ b/mkdocs.yml @@ -1,7 +1,7 @@ site_name: OHAI - Open Hardware Assembly Instructions site_url: https://ohai.opulo.io/ repo_url: https://github.com/opulo-inc/ohai/ -copyright: LumenPnP and its related works are proudly released under the GPL-3.0 license - Opulo Inc 2023 +copyright: LumenPnP and its related works are proudly released under the GPL-3.0 license - Opulo Inc 2024 extra_css: [stylesheets/extra.css] #plugins: @@ -36,12 +36,12 @@ theme: nav: - Home: index.md - - LumenPnP (v3.1): + - LumenPnP: - Introduction: lumen/index.md - Motherboard: lumen/mobo/index.md - X Gantry: lumen/x-gantry/index.md - Y Gantry: lumen/y-gantry/index.md - - Front/Rear Feeder Rail: lumen/feeder-rail/index.md + - Feeder Rail (Front and Rear): lumen/feeder-rail/index.md - Drag Chain: lumen/drag-chain/index.md - Staging Plate: lumen/staging-plate/index.md - Getting Started Kit: misc/ftp-kit/index.md @@ -62,8 +62,8 @@ nav: - Feeder Connection Kit: - Introduction: feeder-connection-kit/index.md - - Feeder Slot PCBA: feeder-connection-kit/panelized-feeder-slot/index.md - - Feeder Slot Set Final Assembly: feeder-connection-kit/slot-set/index.md + - Feeder Blade PCBA: feeder-connection-kit/panelized-feeder-slot/index.md + - Feeder Blade Set Final Assembly: feeder-connection-kit/slot-set/index.md - Feeder Accessory Preparation: feeder-connection-kit/accessories/index.md - Packaging: feeder-connection-kit/packout/index.md