Segmentation Fault on Mac OSX (M1/Monterey)

[andrewwong2000]

Would appreciate some help - am seeing a segmentation fault using the homebrew install process.

Could this related to the UHD library in /opt/homebrew/lib/SoapySDR/modules0.8/libuhdSupport.so being the wrong format for M1?

% SoapySDRUtil --make="driver=uhd,type=b200"
######################################################

Soapy SDR -- the SDR abstraction library

######################################################

Make device driver=uhd,type=b200
[INFO] [UHD] Mac OS; Clang version 13.1.6 (clang-1316.0.21.2); Boost_107800; UHD_4.2.0.HEAD-0-g46a70d85
[INFO] [b200_impl.cpp:421] [B200] Detected Device: B200
[INFO] [B200] Detected Device: B200
[INFO] [b200_impl.cpp:468] [B200] Operating over USB 3.
[INFO] [B200] Operating over USB 3.
[INFO] [b200_impl.cpp:619] [B200] Initialize CODEC control...
[INFO] [B200] Initialize CODEC control...
[INFO] [b200_impl.cpp:688] [B200] Initialize Radio control...
[INFO] [B200] Initialize Radio control...
[INFO] [b200_impl.cpp:1099] [B200] Performing register loopback test...
[INFO] [B200] Performing register loopback test...
[INFO] [b200_impl.cpp:1108] [B200] Register loopback test passed
[INFO] [B200] Register loopback test passed
[INFO] [b200_impl.cpp:815] [B200] Setting master clock rate selection to 'automatic'.
[INFO] [B200] Setting master clock rate selection to 'automatic'.
[INFO] [b200_impl.cpp:1149] [B200] Asking for clock rate 16.000000 MHz...
[INFO] [B200] Asking for clock rate 16.000000 MHz...
[INFO] [b200_impl.cpp:1162] [B200] Actually got clock rate 16.000000 MHz.
[INFO] [B200] Actually got clock rate 16.000000 MHz.
driver=b200
hardware=B200
fpga_version=16.0
fw_version=8.0
mboard_id=B200
mboard_name=MyB200
mboard_serial=3113D17
rx0_antenna=RX2
rx0_id=Unknown (0xffff)
rx0_ref_power_key=b2xx_pwr_rx_rx2
rx0_ref_power_serial=3113D17#A
rx0_serial=
rx0_subdev_name=FE-RX1
rx0_subdev_spec=A:A
tx0_antenna=TX/RX
tx0_id=Unknown (0xffff)
tx0_ref_power_key=b2xx_pwr_tx_tx+rx
tx0_ref_power_serial=3113D17#A
tx0_serial=
tx0_subdev_name=FE-TX1
tx0_subdev_spec=A:A

zsh: segmentation fault SoapySDRUtil --make="driver=uhd,type=b200"

Also:

% SoapySDRUtil --probe="driver=uhd"
######################################################

Soapy SDR -- the SDR abstraction library

######################################################

Probe device driver=uhd
[INFO] [UHD] Mac OS; Clang version 13.1.6 (clang-1316.0.21.2); Boost_107800; UHD_4.2.0.HEAD-0-g46a70d85
[INFO] [b200_impl.cpp:421] [B200] Detected Device: B200
[INFO] [B200] Detected Device: B200
[INFO] [b200_impl.cpp:468] [B200] Operating over USB 3.
[INFO] [B200] Operating over USB 3.
[INFO] [b200_impl.cpp:619] [B200] Initialize CODEC control...
[INFO] [B200] Initialize CODEC control...
[INFO] [b200_impl.cpp:688] [B200] Initialize Radio control...
[INFO] [B200] Initialize Radio control...
[INFO] [b200_impl.cpp:1099] [B200] Performing register loopback test...
[INFO] [B200] Performing register loopback test...
[INFO] [b200_impl.cpp:1108] [B200] Register loopback test passed
[INFO] [B200] Register loopback test passed
[INFO] [b200_impl.cpp:815] [B200] Setting master clock rate selection to 'automatic'.
[INFO] [B200] Setting master clock rate selection to 'automatic'.
[INFO] [b200_impl.cpp:1149] [B200] Asking for clock rate 16.000000 MHz...
[INFO] [B200] Asking for clock rate 16.000000 MHz...
[INFO] [b200_impl.cpp:1162] [B200] Actually got clock rate 16.000000 MHz.
[INFO] [B200] Actually got clock rate 16.000000 MHz.

---

-- Device identification

driver=b200
hardware=B200
fpga_version=16.0
fw_version=8.0
mboard_id=B200
mboard_name=MyB200
mboard_serial=3113D17
rx0_antenna=RX2
rx0_id=Unknown (0xffff)
rx0_ref_power_key=b2xx_pwr_rx_rx2
rx0_ref_power_serial=3113D17#A
rx0_serial=
rx0_subdev_name=FE-RX1
rx0_subdev_spec=A:A
tx0_antenna=TX/RX
tx0_id=Unknown (0xffff)
tx0_ref_power_key=b2xx_pwr_tx_tx+rx
tx0_ref_power_serial=3113D17#A
tx0_serial=
tx0_subdev_name=FE-TX1
tx0_subdev_spec=A:A

---

-- Peripheral summary

Channels: 1 Rx, 1 Tx
Timestamps: YES
Clock sources: internal, external, gpsdo
Time sources: none, internal, external, gpsdo
Sensors: ref_locked
* ref_locked (Ref): false unlocked
GPIOs: FP0, RXA, TXA

---

-- RX Channel 0

Full-duplex: YES
Supports AGC: YES
Stream formats: CS8, CS12, CS16, CF32, CF64
Native format: CS16 [full-scale=32768]
Stream args:
* Samples per packet - The number of samples per packet.
[key=spp, units=samples, default=0, type=int]
* Bus format - The format of samples over the bus.
[key=WIRE, type=string, options=(sc8, sc16)]
* Peak value - The peak value for scaling in complex byte mode.
[key=peak, default=1.0, type=float]
* Receive frame buffer size - The size an individual datagram or frame in bytes.
[key=recv_frame_size, units=bytes, type=int]
* Receive number of buffers - The number of available buffers.
[key=num_recv_frames, units=buffers, type=int]
* Full-scale amplitude - Specifies the full-scale amplitude when using floats (not supported for all devices).
[key=fullscale, default=1.0, type=float]
Antennas: TX/RX, RX2
Corrections: DC removal
Full gain range: [0, 76, 1] dB
PGA gain range: [0, 76, 1] dB
Full freq range: [42, 6008] MHz
RF freq range: [42, 6008] MHz
BB freq range: [-8, 8] MHz
Tune args:
* N divider - Whether the daughterboard tune code should use an integer N divider or fractional N divider (not supported for all devices).
[key=mode_n, type=string, options=(integer, fractional)]
* Integer-N tuning step - The step between valid tunable frequencies when using integer-N tuning (not supported for all devices).
[key=int_n_step, type=float]
Sample rates: 0.03125, 0.0314961, 0.031746, 0.032, 0.0322581, ..., 3.2, 4, 5.33333, 8, 16 MSps
Filter bandwidths: [0.2, 56] MHz
Sensors: temp, rssi, lo_locked
* temp (temp): 34.912285 C
* rssi (RSSI): -50.750000 dB
* lo_locked (LO): true locked

---

-- TX Channel 0

Full-duplex: YES
Supports AGC: NO
Stream formats: CS8, CS12, CS16, CF32, CF64
Native format: CS16 [full-scale=32768]
Stream args:
* Samples per packet - The number of samples per packet.
[key=spp, units=samples, default=0, type=int]
* Bus format - The format of samples over the bus.
[key=WIRE, type=string, options=(sc8, sc16)]
* Peak value - The peak value for scaling in complex byte mode.
[key=peak, default=1.0, type=float]
* Send frame buffer size - The size an individual datagram or frame in bytes.
[key=send_frame_size, units=bytes, type=int]
* Send number of buffers - The number of available buffers.
[key=num_send_frames, units=buffers, type=int]
* Full-scale amplitude - Specifies the full-scale amplitude when using floats (not supported for all devices).
[key=fullscale, default=1.0, type=float]
* Underflow policy - How the TX DSP should recover from underflow (not supported for all devices).
[key=underflow_policy, type=string, options=(next_burst, next_packet)]
Antennas: TX/RX
Full gain range: [0, 89.75, 0.25] dB
PGA gain range: [0, 89.75, 0.25] dB
Full freq range: [42, 6008] MHz
RF freq range: [42, 6008] MHz
BB freq range: [-8, 8] MHz
Tune args:
* N divider - Whether the daughterboard tune code should use an integer N divider or fractional N divider (not supported for all devices).
[key=mode_n, type=string, options=(integer, fractional)]
* Integer-N tuning step - The step between valid tunable frequencies when using integer-N tuning (not supported for all devices).
[key=int_n_step, type=float]
Sample rates: 0.03125, 0.0314961, 0.031746, 0.032, 0.0322581, ..., 3.2, 4, 5.33333, 8, 16 MSps
Filter bandwidths: [0.2, 56] MHz
Sensors: temp, lo_locked
* temp (temp): 34.912285 C
* lo_locked (LO): true locked

zsh: segmentation fault SoapySDRUtil --probe="driver=uhd"

[nzqo]

Did you ever manage to figure something out about this? I am facing the same issue, almost a year later, and there seems to have been no answer anywhere since then