[Anycubic Photon mono 7 pro] Incorrect layer thickness

[JKBert]

Hello,

I'm trying to print some pieces on a Photon mono 7 pro printer. Slicing has been done through prusa-slicer and I just use UVtools to configure timing and to convert SL1 file to PWSZ. I use UVtools on a Linux Debian Workstation (amd64). I have built from sources UVtools 5.0.5.

When conversion is done, I copy file to an USB stick and I try to print directly from this USB stick. Printer refuses to use this file and only prints "file parameter, incorrect layer thickness".

I have checked twice all parameters and I don't understand. If I go into generated file, layers_controller.conf contains:

...
    {
      "exposure_time": 35,
      "layer_index": 0,
      "layer_minheight": 0,
      "layer_thickness": 0.05,
      "zup_height": 8,
      "zup_speed": 6
    },
...

I don't understand why printer cannot use this file. Does someone is able to send a file to a Photon mono 7 pro ?

Best regards,

JB

[JKBert]

I've just opened a example provided by Anycubic and in this file, layer thickness is set to "layer_thickness": 0.05000000074505806.

[JKBert]

Oops, sorry. newton only understands IPv4, not IPv6... It's a VAXserver running OpenVMS 7.3. Fixed.

[sn4k3]

I was using FileZilla, the dns resolve to ipv6...

[JKBert]

I have tried to install Anycubic slicer (anycubicphotonworkshop), but without success. I only have Linux/Unix workstation. Under wine, official slicer doesn't start. In a vm (Windows 10), it complains against OpenGL... I cannot compare file generated by UVtools and file generated by official tools.

Here is layers_controller.conf generated by UVtools:

{
  "count": 2940,
  "paras": [
    {
      "exposure_time": 35,
      "layer_index": 0,
      "layer_minheight": 0,
      "layer_thickness": 0.05,
      "zup_height": 8,
      "zup_speed": 6
    },
    {
      "exposure_time": 35,
      "layer_index": 1,
      "layer_minheight": 0.05,
      "layer_thickness": 0.05,
      "zup_height": 8,
      "zup_speed": 6
    },
    {
      "exposure_time": 35,
      "layer_index": 2,
      "layer_minheight": 0.1,
      "layer_thickness": 0.05,
      "zup_height": 8,
      "zup_speed": 6
    },
    {
      "exposure_time": 35,
      "layer_index": 3,
      "layer_minheight": 0.15,
      "layer_thickness": 0.05,
      "zup_height": 8,
      "zup_speed": 6
    },
...
  ]
}

and now, example file provided by Anycubic:

    "count": 288,
    "paras": [
        {
            "exposure_time": 25.0,
            "layer_index": 0,
            "layer_minheight": 0.0,
            "layer_thickness": 0.05000000074505806,
            "zup_height": 8.0,
            "zup_speed": 6.0
        },
        {
            "exposure_time": 25.0,
            "layer_index": 1,
            "layer_minheight": 0.05000000074505806,
            "layer_thickness": 0.05000000074505806,
            "zup_height": 8.0,
            "zup_speed": 6.0
        },
        {
            "exposure_time": 25.0,
            "layer_index": 2,
            "layer_minheight": 0.10000000149011612,
            "layer_thickness": 0.05000000074505806,
            "zup_height": 8.0,
            "zup_speed": 6.0
        },
...
   ]
}

Only one difference between these files: float format. I haven't found a file generated by Anycubic slicer with "layer_thickness": 0.05. I will try tomorrow to fix with a script all layer_thickness values to multiples of 0.05000000074505806.

[sn4k3]

Again problem is not from there...
Chitubox works on linux?

[sn4k3]

The file you sent was sliced into Chitubox?

[JKBert]

Tiago Conceição a écrit :

The file you sent was sliced into Chitubox?

Yes, as your slicer doesn't run on Linux. Best regards, JB

[sn4k3]

But I thought you were using PrusaSlicer?

[JKBert]

Tiago Conceição a écrit :

But I thought you were using PrusaSlicer?

I beg your pardon, I have opened a tocket at Anycubic support and I mixed both... I have tried, in a first time, to use PrusaSlicer and UVtools (from 5.0.2 to 5.0.5). Without success. If UVtools generates a PWSZ file, printer always complains about slice thickness. In a second time, I have generated the same file with Chitubox. Printer accepts this new file but I have some trouble with parameters (delamination). Best regards, JB

[sn4k3]

I think problem is in anycubic_photon_resins.pwsp file.
On a working file, open as zip and remove anycubic_photon_resins.pwsp file, try to print. If it fails replace that file with the one from PrusaSlicer, print and test. If still fails problem is on that file. Report back with the results.