OpenT12.ino

/////////////////////////////////////////////////////////////////
#include "OpenT12.h"
/*
自己动手
样样有！
*/

//重设蓝牙串口缓冲区大小
#define RX_QUEUE_SIZE 2048
#define TX_QUEUE_SIZE 2048

/////////////////////////////////////////////////////////////////
BluetoothSerial SerialBT;
#if !defined(CONFIG_BT_ENABLED) || !defined(CONFIG_BLUEDROID_ENABLED)
#error Bluetooth is not enabled! Please run `make menuconfig` to and enable it
#endif

OneButton RButton(BUTTON_PIN, true);
/*
 * 此处因为不是代表esp32的 IO22,IO23接口，所以需要用SW模式->即软件开关
 * 因为屏幕方向倒转，所以需要使用U8G2_R2模式->即翻转180度
 */
U8G2_SSD1306_128X64_NONAME_F_SW_I2C Disp(U8G2_R2,/* clock=*/ 13, /* data=*/ 15, /* reset=*/ U8X8_PIN_NONE); //(rotation, clock, data [, reset])
//U8G2_SSD1306_128X64_NONAME_F_HW_I2C Disp(U8G2_R0,/* clock=*/ 13, /* data=*/ 15, /* reset=*/ U8X8_PIN_NONE); //(rotation, clock, data [, reset])
//U8G2_SSD1306_128X64_NONAME_F_4W_SW_SPI Disp(U8G2_R0, /* clock=*/ 13, /* data=*/ 11, /* cs=*/ 10, /* dc=*/ 9, /* reset=*/ 8);
//U8G2_SSD1306_128X64_NONAME_F_4W_HW_SPI Disp(U8G2_R0, /* cs=*/ 5, /* dc=*/ 13, /* reset=*/ 15);
PID MyPID(&TipTemperature, &PID_Output, &PID_Setpoint, aggKp, aggKi, aggKd, DIRECT);
/////////////////////////////////////////////////////////////////
uint8_t _MODE = true;

char* TipName = "文件系统错误：请上报";

float BootTemp = 300;      //开机温度          (°C)
float SleepTemp = 150;     //休眠温度          (°C)
float BoostTemp = 50;      //爆发模式升温幅度   (°C)

float ShutdownTime        = 0;      //关机提醒              (分)
float SleepTime           = 4;      //休眠触发时间          (分)
float ScreenProtectorTime = 60;     //屏保在休眠后的触发时间(秒)
float BoostTime           = 30;     //爆发模式持续时间      (秒)


bool SYS_Ready = false;
//烙铁头事件
bool TipInstallEvent   = true;
bool TipCallSleepEvent    = false;
//到温提示音播放完成
bool TempToneFlag = false;
//休眠后屏保延迟显示标志
bool SleepScreenProtectFlag = false;
//温控系统状态
bool ERROREvent        = false;
bool ShutdownEvent     = false;
bool SleepEvent        = false;
bool BoostEvent        = false;
bool UnderVoltageEvent = false;
//PWM控制状态
bool PWM_WORKY         = false;

uint8_t PIDMode                     = true;
uint8_t Use_KFP                     = true;
uint8_t PanelSettings               = PANELSET_Detailed;
uint8_t ScreenFlip                  = false;
uint8_t SmoothAnimation_Flag        = true;
float   ScreenBrightness            = 128;
uint8_t OptionStripFixedLength_Flag = false;

uint8_t Volume = false;
uint8_t RotaryDirection = false;
uint8_t HandleTrigger = HANDLETRIGGER_VibrationSwitch;

double  SYS_Voltage = 3.3;
double  NTC_Temp    = 27.0;
float   UndervoltageAlert = 3;
char    BootPasswd[20] = { 0 };
uint8_t Language = LANG_Chinese;
uint8_t MenuListMode = false;

float ADC_PID_Cycle = 100;

//面板状态条
uint8_t TempCTRL_Status = TEMP_STATUS_OFF;
uint8_t* C_table[] = { c1, c2, c3, Lightning, c5, c6, c7 };
char* TempCTRL_Status_Mes[]={
    "错误",
    "停机",
    "休眠",
    "提温",
    "正常",
    "加热",
    "维持",
};

//系统信息
uint64_t ChipMAC;
char ChipMAC_S[19] = { 0 };
char CompileTime[20];
//定时器
hw_timer_t* SoundTimer = NULL;
/////////////////////////////////////////////////////////////////

//先初始化硬件->显示LOGO->初始化软件
void setup() {
    //关闭中断
    noInterrupts();
    ////////////////////////////初始化硬件/////////////////////////////
    //获取系统信息
    ChipMAC = ESP.getEfuseMac();
    sprintf(CompileTime, "%s %s", __DATE__, __TIME__);
    for (uint8_t i = 0;i < 6;i++)  sprintf(ChipMAC_S + i * 3, "%02X%s", ((uint8_t*)&ChipMAC)[i], (i != 5) ? ":" : "");

    //初始化串口
    Serial.begin(115200);

    //初始化GPIO
    BeepInit();                     //蜂鸣器
    
    // pinMode(LED_Pin, OUTPUT);       //软件运行指示LED
    pinMode(POWER_ADC_PIN, INPUT);  //主电压分压检测ADC


    //初始化烙铁头
    TipControlInit();

    //初始化编码器
    sys_RotaryInit();

    //初始化OLED
    Disp.begin();
    // Disp.setBusClock(921600);
    Disp.enableUTF8Print();
    Disp.setFontDirection(0);
    Disp.setFontPosTop();
    Disp.setFont(u8g2_font_wqy12_t_gb2312);
    Disp.setDrawColor(1);
    Disp.setFontMode(1);

    

    ////////////////////////////初始化软件/////////////////////////////
    //显示启动信息
    //ShowBootMsg();

    //启动文件系统，并读取存档
    FilesSystemInit();

    //初始化命令解析器
    shellInit();

    //初始化蓝牙（可选）
    BLE_Init();

    //首次启动的时候根据启动温度配置，重新设定目标温度
    sys_Counter_SetVal(BootTemp);

    //载入烙铁头配置
    LoadTipConfig();

    SetSound(BootSound); //播放音效

    //显示Logo
    EnterLogo();
    
    //开机密码
    while (!EnterPasswd()) {
        Pop_Windows("身份验证失败");
    }

    //初始化UI
    System_UI_Init();


    SYS_Ready = true;
    
    // ShutdownEventLoop();
}

void loop() {
    //获取按键
    sys_KeyProcess();

    if (!Menu_System_State) {
        //温度闭环控制
        TemperatureControlLoop();
        //更新系统事件：：系统事件可能会改变功率输出
        TimerEventLoop();
    }

    
    //更新状态码
    SYS_StateCode_Update();
    //设置输出功率
    SetPOWER(PID_Output);

    //刷新UI
    System_UI();
}


void SYS_Reboot(void) {
    ESP.restart();
}

void About(void) {
    //播放Logo动画
    EnterLogo();
    //生成项目QRCode
    QRCode qrcode;
    uint8_t qrcodeData[qrcode_getBufferSize(3)];

    switch (Language) {
        case LANG_Chinese:
            // qrcode_initText(&qrcode, qrcodeData, 3, 0, "https://gitee.com/createskyblue/OpenT12");   //禁用Gitee源:注册不方便
            qrcode_initText(&qrcode, qrcodeData, 3, 0, "https://github.com/createskyblue/OpenT12");
        break;

        default:
            qrcode_initText(&qrcode, qrcodeData, 3, 0, "https://github.com/createskyblue/OpenT12");
        break;
    }

    Clear();

    uint8_t x_offset = (SCREEN_COLUMN - qrcode.size*2)/2;
    uint8_t y_offset = (SCREEN_ROW - qrcode.size*2)/2;
    
    for (uint8_t y=0;y<qrcode.size;y++)
        for (uint8_t x=0;x<qrcode.size;x++)
            if (qrcode_getModule(&qrcode, x, y)) Draw_Pixel_Resize(x + x_offset,y + y_offset,x_offset,y_offset,2,2);

    Disp.setDrawColor(2);
    Disp.drawBox(x_offset - 2 ,y_offset - 2 ,qrcode.size * 2 + 4,qrcode.size * 2 + 4);
    Disp.setDrawColor(1);

    while(!sys_KeyProcess()) {
        Display();
    }

}