Skip to content

Eytecz/LGX_Lite_Stealthburner_CW2_style_mount

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

16 Commits
 
 
 
 
 
 

Repository files navigation

LGX_Lite_Stealthburner_CW2_style_mount

LGX Lite extruder mount for the Voron Stealthburner. The standard bowden clip delivered with the LGX Lite is to be removed, and a standard UM2 connector has to be inserted in the top printed part. This style clip is to be used: https://nl.aliexpress.com/item/32896103430.html. If you're lucky you might have some laying around already.

LGX Lite mount ERCF

The ERCF version is made to accomodate the LGX Lite with the stealthburner and the new carriage, including the toolhead sensor as it is being used for the ERCF. The housing style is matching with the original CW2 design. I recommend to insert a 3mm long 4x2mm bowden tube on the bottom of the LGX Lite to guide the filament properly. The cover and cable carrier mount can be re-used from the original version. The top of the front body is made to insert the bowden tube until it reaches into the LGX Lite, through a standard bowden tube clip with retainer ring. A lever latch is designed to change the pretension on the filament.

2022-08-10 21_20_59-Solid Edge 2022 - Assembly -  LGX_Lite_Stealthburner_ERCF asm

The toolhead sensor is a standard hall effect switch (AH3364Q-P-B), which can be soldered to some wires with a connector. This sensor enters in between both halves of the support body and can be fixed using an angled M3x8 DIN912 bolt. Please be careful not to overtighten this bolt as it clamps directly onto the sensor housing. A standard washer M3 is to be inserted in the slot centered with the filament path. The magnet can be inserted in the front. Be sure to check the correct polarity.

To mount the LGX Lite to the body, use the 4 screws DIN912 M3x16mm, too long screws will damage the gears within the LGX!

Optionally one can choose to use the PCB version, which supports the Hartk Stealthburner PCB.

2022-10-04 20_12_45-Solid Edge 2022 - Assembly -  LGX_Lite_Stealthburner_ERCF asm

M3 Threaded insert locations

In the front housing there are 2 threaded inserts M3 which needs to be placed on the 'inside' to fixate the actual Stealthburner cover to.

2022-08-10 21_23_19-Solid Edge 2022 - Assembly -  LGX_Lite_Stealthburner_ERCF asm

In the rear housing there are 4 threaded inserts M3 to be placed on the back as shown in the image below.

2022-08-10 21_24_36-Solid Edge 2022 - Assembly -  LGX_Lite_Stealthburner_ERCF asm

Cable hatch and cable carrier

The standard cable door hatch and cable carrier support can be re-used from the original CW2. Be sure to mount the cable door before mounting the LGX Lite into the housing. You won't be able to reach the fastener once the LGX Lite is placed.

2022-08-10 21_26_32-Solid Edge 2022 - Assembly -  LGX_Lite_Stealthburner_ERCF asm

Optional for the PCB version is the enlarged cover.

2022-10-04 20_12_10-Solid Edge 2022 - Assembly -  LGX_Lite_Stealthburner_ERCF asm

I am not responsible in any way on how this impacts your printer. Use at your own risk.

About

LGX Lite extruder mount for the Voron Stealthburner.

Resources

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published