New Zigbee plugs with Energy meter

docs/devices/4058075208407.md

@@ -0,0 +1,110 @@
+---
+title: "LEDVANCE 4058075208407 control via MQTT"
+description: "Integrate your LEDVANCE 4058075208407 via Zigbee2MQTT with whatever smart home infrastructure you are using without the vendor's bridge or gateway."
+addedAt: 2024-01-19T15:06:58
+pageClass: device-page
+---
+
+<!-- !!!! -->
+<!-- ATTENTION: This file is auto-generated through docgen! -->
+<!-- You can only edit the "Notes"-Section between the two comment lines "Notes BEGIN" and "Notes END". -->
+<!-- Do not use h1 or h2 heading within "## Notes"-Section. -->
+<!-- !!!! -->
+
+# LEDVANCE 4058075208407
+
+|     |     |
+|-----|-----|
+| Model | 4058075208407  |
+| Vendor  | [LEDVANCE](/supported-devices/#v=LEDVANCE)  |
+| Description | SMART+ lamp B22D RGBTW |
+| Exposes | light (state, brightness, color_temp, color_xy, color_hs), effect, power_on_behavior, linkquality |
+| Exposes | light (state, brightness, color_temp, color_xy, color_hs), effect, linkquality |
+| Picture | ![LEDVANCE 4058075208407](https://www.zigbee2mqtt.io/images/devices/4058075208407.jpg) |
+
+
+<!-- Notes BEGIN: You can edit here. Add "## Notes" headline if not already present. -->
+
+
+<!-- Notes END: Do not edit below this line -->
+
+
+## OTA updates
+This device supports OTA updates, for more information see [OTA updates](../guide/usage/ota_updates.md).
+
+
+## Options
+*[How to use device type specific configuration](../guide/configuration/devices-groups.md#specific-device-options)*
+
+* `transition`: Controls the transition time (in seconds) of on/off, brightness, color temperature (if applicable) and color (if applicable) changes. Defaults to `0` (no transition). The value must be a number with a minimum value of `0`
+
+* `color_sync`: When enabled colors will be synced, e.g. if the light supports both color x/y and color temperature a conversion from color x/y to color temperature will be done when setting the x/y color (default true). The value must be `true` or `false`
+
+* `state_action`: State actions will also be published as 'action' when true (default false). The value must be `true` or `false`
+
+
+## Exposes
+
+### Light 
+This light supports the following features: `state`, `brightness`, `color_temp`, `color_xy`, `color_hs`.
+- `state`: To control the state publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"state": "ON"}`, `{"state": "OFF"}` or `{"state": "TOGGLE"}`. To read the state send a message to `zigbee2mqtt/FRIENDLY_NAME/get` with payload `{"state": ""}`.
+- `brightness`: To control the brightness publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"brightness": VALUE}` where `VALUE` is a number between `0` and `254`. To read the brightness send a message to `zigbee2mqtt/FRIENDLY_NAME/get` with payload `{"brightness": ""}`.
+- `color_temp`: To control the color temperature (in reciprocal megakelvin a.k.a. mired scale) publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"color_temp": VALUE}` where `VALUE` is a number between `153` and `370`, the higher the warmer the color. To read the color temperature send a message to `zigbee2mqtt/FRIENDLY_NAME/get` with payload `{"color_temp": ""}`. Besides the numeric values the following values are accepected: `coolest`, `cool`, `neutral`, `warmest`.
+- `color_xy`: To control the XY color (CIE 1931 color space) publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"color": {"x": X_VALUE, "y": Y_VALUE}}` (e.g. `{"color":{"x":0.123,"y":0.123}}`). To read the XY color send a message to `zigbee2mqtt/FRIENDLY_NAME/get` with payload `{"color":{"x":"","y":""}}`. Alternatively it is possible to set the XY color via RGB:
+  - `{"color": {"r": R, "g": G, "b": B}}` e.g. `{"color":{"r":46,"g":102,"b":150}}`
+  - `{"color": {"rgb": "R,G,B"}}` e.g. `{"color":{"rgb":"46,102,150"}}`
+  - `{"color": {"hex": HEX}}` e.g. `{"color":{"hex":"#547CFF"}}`
+- `color_hs`: To control the hue/saturation (color) publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"color": {"hue": HUE, "saturation": SATURATION}}` (e.g. `{"color":{"hue":360,"saturation":100}}`). To read the hue/saturation send a message to `zigbee2mqtt/FRIENDLY_NAME/get` with payload `{"color":{"hue":"","saturation":""}}`. Alternatively it is possible to set the hue/saturation via:
+  - HSB space (hue, saturation, brightness): `{"color": {"h": H, "s": S, "b": B}}` e.g. `{"color":{"h":360,"s":100,"b":100}}` or `{"color": {"hsb": "H,S,B"}}` e.g. `{"color":{"hsb":"360,100,100"}}`
+  - HSV space (hue, saturation, value):`{"color": {"h": H, "s": S, "v": V}}` e.g. `{"color":{"h":360,"s":100,"v":100}}` or `{"color": {"hsv": "H,S,V"}}` e.g. `{"color":{"hsv":"360,100,100"}}`
+  - HSL space (hue, saturation, lightness)`{"color": {"h": H, "s": S, "l": L}}` e.g. `{"color":{"h":360,"s":100,"l":100}}` or `{"color": {"hsl": "H,S,L"}}` e.g. `{"color":{"hsl":"360,100,100"}}`
+
+#### Transition
+For all of the above mentioned features it is possible to do a transition of the value over time. To do this add an additional property `transition` to the payload which is the transition time in seconds.
+Examples: `{"brightness":156,"transition":3}`, `{"color_temp":241,"transition":1}`.
+
+#### Moving/stepping
+Instead of setting a value (e.g. brightness) directly it is also possible to:
+- move: this will automatically move the value over time, to stop send value `stop` or `0`.
+- step: this will increment/decrement the current value by the given one.
+
+The direction of move and step can be either up or down, provide a negative value to move/step down, a positive value to move/step up.
+To do this send a payload like below to `zigbee2mqtt/FRIENDLY_NAME/set`
+
+**NOTE**: brightness move/step will stop at the minimum brightness and won't turn on the light when it's off. In this case use `brightness_move_onoff`/`brightness_step_onoff`
+````js
+{
+  "brightness_move": -40, // Starts moving brightness down at 40 units per second
+  "brightness_move": 0, // Stop moving brightness
+  "brightness_step": 40 // Increases brightness by 40
+  "color_temp_move": 60, // Starts moving color temperature up at 60 units per second
+  "color_temp_move": "stop", // Stop moving color temperature
+  "color_temp_step": 99, // Increase color temperature by 99
+  "hue_move": 40, // Starts moving hue up at 40 units per second, will endlessly loop (allowed value range: -255 till 255)
+  "hue_step": -90, // Decrease hue by 90 (allowed value range: -255 till 255)
+  "saturation_move": -55, // Starts moving saturation down at -55 units per second (allowed value range: -255 till 255)
+  "saturation_step": 66, // Increase saturation by 66 (allowed value range: -255 till 255)
+}
+````
+
+### Effect (enum)
+Triggers an effect on the light (e.g. make light blink for a few seconds).
+Value will **not** be published in the state.
+It's not possible to read (`/get`) this value.
+To write (`/set`) a value publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"effect": NEW_VALUE}`.
+The possible values are: `blink`, `breathe`, `okay`, `channel_change`, `finish_effect`, `stop_effect`.
+
+### Power_on_behavior (enum)
+Controls the behavior when the device is powered on after power loss.
+Value can be found in the published state on the `power_on_behavior` property.
+To read (`/get`) the value publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/get` with payload `{"power_on_behavior": ""}`.
+To write (`/set`) a value publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"power_on_behavior": NEW_VALUE}`.
+The possible values are: `off`, `on`, `toggle`, `previous`.
+
+### Linkquality (numeric)
+Link quality (signal strength).
+Value can be found in the published state on the `linkquality` property.
+It's not possible to read (`/get`) or write (`/set`) this value.
+The minimal value is `0` and the maximum value is `255`.
+The unit of this value is `lqi`.
+

docs/devices/4058075729025.md

@@ -18,6 +18,7 @@ pageClass: device-page
 | Model | 4058075729025  |
 | Vendor  | [LEDVANCE](/supported-devices/#v=LEDVANCE)  |
 | Description | SMART+ lamp E27 RGBTW |
+| Exposes | light (state, brightness, color_temp, color_xy, color_hs), effect, power_on_behavior, linkquality |
 | Exposes | light (state, brightness, color_temp, color_xy, color_hs), effect, linkquality |
 | Picture | ![LEDVANCE 4058075729025](https://www.zigbee2mqtt.io/images/devices/4058075729025.jpg) |
 
@@ -93,6 +94,13 @@ It's not possible to read (`/get`) this value.
 To write (`/set`) a value publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"effect": NEW_VALUE}`.
 The possible values are: `blink`, `breathe`, `okay`, `channel_change`, `finish_effect`, `stop_effect`.
 
+### Power_on_behavior (enum)
+Controls the behavior when the device is powered on after power loss.
+Value can be found in the published state on the `power_on_behavior` property.
+To read (`/get`) the value publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/get` with payload `{"power_on_behavior": ""}`.
+To write (`/set`) a value publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"power_on_behavior": NEW_VALUE}`.
+The possible values are: `off`, `on`, `toggle`, `previous`.
+
 ### Linkquality (numeric)
 Link quality (signal strength).
 Value can be found in the published state on the `linkquality` property.

docs/devices/4058075729049.md

@@ -18,6 +18,7 @@ pageClass: device-page
 | Model | 4058075729049  |
 | Vendor  | [LEDVANCE](/supported-devices/#v=LEDVANCE)  |
 | Description | SMART+ lamp B22D RGBTW |
+| Exposes | light (state, brightness, color_temp, color_xy, color_hs), effect, power_on_behavior, linkquality |
 | Exposes | light (state, brightness, color_temp, color_xy, color_hs), effect, linkquality |
 | Picture | ![LEDVANCE 4058075729049](https://www.zigbee2mqtt.io/images/devices/4058075729049.jpg) |
 
@@ -93,6 +94,13 @@ It's not possible to read (`/get`) this value.
 To write (`/set`) a value publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"effect": NEW_VALUE}`.
 The possible values are: `blink`, `breathe`, `okay`, `channel_change`, `finish_effect`, `stop_effect`.
 
+### Power_on_behavior (enum)
+Controls the behavior when the device is powered on after power loss.
+Value can be found in the published state on the `power_on_behavior` property.
+To read (`/get`) the value publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/get` with payload `{"power_on_behavior": ""}`.
+To write (`/set`) a value publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"power_on_behavior": NEW_VALUE}`.
+The possible values are: `off`, `on`, `toggle`, `previous`.
+
 ### Linkquality (numeric)
 Link quality (signal strength).
 Value can be found in the published state on the `linkquality` property.

docs/devices/4058075729087.md

@@ -0,0 +1,114 @@
+---
+title: "LEDVANCE 4058075729087 control via MQTT"
+description: "Integrate your LEDVANCE 4058075729087 via Zigbee2MQTT with whatever smart home infrastructure you are using without the vendor's bridge or gateway."
+addedAt: 2022-11-22T22:24:43Z
+pageClass: device-page
+---
+
+<!-- !!!! -->
+<!-- ATTENTION: This file is auto-generated through docgen! -->
+<!-- You can only edit the "Notes"-Section between the two comment lines "Notes BEGIN" and "Notes END". -->
+<!-- Do not use h1 or h2 heading within "## Notes"-Section. -->
+<!-- !!!! -->
+
+# LEDVANCE 4058075729087
+
+|     |     |
+|-----|-----|
+| Model | 4058075729087  |
+| Vendor  | [LEDVANCE](/supported-devices/#v=LEDVANCE)  |
+| Description | SMART+ CL B40 E14 Tunable white |
+| Exposes | light (state, brightness, color_temp), effect, linkquality |
+| Picture | ![LEDVANCE 4058075729087](https://www.zigbee2mqtt.io/images/devices/4058075729087.jpg) |
+
+
+<!-- Notes BEGIN: You can edit here. Add "## Notes" headline if not already present. -->
+## Notes
+
+
+### Set default power on/off transition
+Various LEDVANCE Products support setting a default transition when turning a light on and off.
+
+**TOPIC**: `zigbee2mqtt/FRIENDLY_NAME/set`
+```js
+{
+    "set_transition": 1
+}
+```
+**INFO**: Value is time in seconds (integer, float values are not supported)
+
+### Remember current light state
+Various Osram/Sylvania LED support remembering their current state in case of power loss, or if a light
+is manually switched off then on. Lights will remember their respective attributes
+(i.e. brightness, color, saturation, etc.).
+**NOTE**: This must be executed every time you make changes to a light's attributes for it to then 'remember' it.
+
+**TOPIC**: `zigbee2mqtt/FRIENDLY_NAME/set`
+```js
+{
+    "remember_state": true
+}
+```
+**INFO**: Value is true, false (boolean)
+<!-- Notes END: Do not edit below this line -->
+
+## OTA updates
+This device supports OTA updates, for more information see [OTA updates](../guide/usage/ota_updates.md).
+
+
+## Options
+*[How to use device type specific configuration](../guide/configuration/devices-groups.md#specific-device-options)*
+
+* `transition`: Controls the transition time (in seconds) of on/off, brightness, color temperature (if applicable) and color (if applicable) changes. Defaults to `0` (no transition). The value must be a number with a minimum value of `0`
+
+* `color_sync`: When enabled colors will be synced, e.g. if the light supports both color x/y and color temperature a conversion from color x/y to color temperature will be done when setting the x/y color (default true). The value must be `true` or `false`
+
+* `state_action`: State actions will also be published as 'action' when true (default false). The value must be `true` or `false`
+
+
+## Exposes
+
+### Light 
+This light supports the following features: `state`, `brightness`, `color_temp`.
+- `state`: To control the state publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"state": "ON"}`, `{"state": "OFF"}` or `{"state": "TOGGLE"}`. To read the state send a message to `zigbee2mqtt/FRIENDLY_NAME/get` with payload `{"state": ""}`.
+- `brightness`: To control the brightness publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"brightness": VALUE}` where `VALUE` is a number between `0` and `254`. To read the brightness send a message to `zigbee2mqtt/FRIENDLY_NAME/get` with payload `{"brightness": ""}`.
+- `color_temp`: To control the color temperature (in reciprocal megakelvin a.k.a. mired scale) publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"color_temp": VALUE}` where `VALUE` is a number between `153` and `370`, the higher the warmer the color. To read the color temperature send a message to `zigbee2mqtt/FRIENDLY_NAME/get` with payload `{"color_temp": ""}`. Besides the numeric values the following values are accepected: `coolest`, `cool`, `neutral`, `warmest`.
+
+#### Transition
+For all of the above mentioned features it is possible to do a transition of the value over time. To do this add an additional property `transition` to the payload which is the transition time in seconds.
+Examples: `{"brightness":156,"transition":3}`, `{"color_temp":241,"transition":1}`.
+
+#### Moving/stepping
+Instead of setting a value (e.g. brightness) directly it is also possible to:
+- move: this will automatically move the value over time, to stop send value `stop` or `0`.
+- step: this will increment/decrement the current value by the given one.
+
+The direction of move and step can be either up or down, provide a negative value to move/step down, a positive value to move/step up.
+To do this send a payload like below to `zigbee2mqtt/FRIENDLY_NAME/set`
+
+**NOTE**: brightness move/step will stop at the minimum brightness and won't turn on the light when it's off. In this case use `brightness_move_onoff`/`brightness_step_onoff`
+````js
+{
+  "brightness_move": -40, // Starts moving brightness down at 40 units per second
+  "brightness_move": 0, // Stop moving brightness
+  "brightness_step": 40 // Increases brightness by 40
+  "color_temp_move": 60, // Starts moving color temperature up at 60 units per second
+  "color_temp_move": "stop", // Stop moving color temperature
+  "color_temp_step": 99, // Increase color temperature by 99
+}
+````
+
+### Effect (enum)
+Triggers an effect on the light (e.g. make light blink for a few seconds).
+Value will **not** be published in the state.
+It's not possible to read (`/get`) this value.
+To write (`/set`) a value publish a message to topic `zigbee2mqtt/FRIENDLY_NAME/set` with payload `{"effect": NEW_VALUE}`.
+The possible values are: `blink`, `breathe`, `okay`, `channel_change`, `finish_effect`, `stop_effect`.
+
+### Linkquality (numeric)
+Link quality (signal strength).
+Value can be found in the published state on the `linkquality` property.
+It's not possible to read (`/get`) or write (`/set`) this value.
+The minimal value is `0` and the maximum value is `255`.
+The unit of this value is `lqi`.
+