Merge pull request #2563 from wjklimek1/master

Support for STM32H503 MCU

hw/bsp/stm32h5/boards/stm32h503nucleo/board.cmake

@@ -0,0 +1,8 @@
+set(MCU_VARIANT stm32h503xx)
+set(JLINK_DEVICE stm32h503rb)
+
+function(update_board TARGET)
+  target_compile_definitions(${TARGET} PUBLIC
+    STM32H503xx
+    )
+endfunction()

hw/bsp/stm32h5/boards/stm32h503nucleo/board.h

@@ -0,0 +1,122 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2020, Ha Thach (tinyusb.org)
+ * Copyright (c) 2023, HiFiPhile
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+// LED
+#define LED_PORT              GPIOA
+#define LED_PIN               GPIO_PIN_5
+#define LED_STATE_ON          1
+
+// Button
+#define BUTTON_PORT           GPIOA
+#define BUTTON_PIN            GPIO_PIN_0
+#define BUTTON_STATE_ACTIVE   0
+
+// UART Enable for STLink VCOM
+#define UART_DEV              USART3
+#define UART_CLK_EN           __USART3_CLK_ENABLE
+#define UART_GPIO_PORT        GPIOA
+#define UART_GPIO_AF          GPIO_AF13_USART3
+
+#define UART_TX_PIN           GPIO_PIN_3
+#define UART_RX_PIN           GPIO_PIN_4
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+static inline void SystemClock_Config(void) {
+  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
+  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
+
+  /** Configure the main internal regulator output voltage
+  */
+  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE0);
+
+  while(!__HAL_PWR_GET_FLAG(PWR_FLAG_VOSRDY)) {}
+
+  /** Initializes the RCC Oscillators according to the specified parameters
+  * in the RCC_OscInitTypeDef structure.
+  */
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48|RCC_OSCILLATORTYPE_HSE;
+  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+  RCC_OscInitStruct.HSI48State = RCC_HSI48_ON;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLL1_SOURCE_HSE;
+  RCC_OscInitStruct.PLL.PLLM = 12;
+  RCC_OscInitStruct.PLL.PLLN = 250;
+  RCC_OscInitStruct.PLL.PLLP = 2;
+  RCC_OscInitStruct.PLL.PLLQ = 2;
+  RCC_OscInitStruct.PLL.PLLR = 2;
+  RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1_VCIRANGE_1;
+  RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1_VCORANGE_WIDE;
+  RCC_OscInitStruct.PLL.PLLFRACN = 0;
+  HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+  /** Initializes the CPU, AHB and APB buses clocks
+  */
+  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
+                                |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2
+                                |RCC_CLOCKTYPE_PCLK3;
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+  RCC_ClkInitStruct.APB3CLKDivider = RCC_HCLK_DIV1;
+  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
+
+  // Configure CRS clock source
+  __HAL_RCC_CRS_CLK_ENABLE();
+  RCC_CRSInitTypeDef RCC_CRSInitStruct = {0};
+  RCC_CRSInitStruct.Prescaler = RCC_CRS_SYNC_DIV1;
+  RCC_CRSInitStruct.Source = RCC_CRS_SYNC_SOURCE_USB;
+  RCC_CRSInitStruct.Polarity = RCC_CRS_SYNC_POLARITY_RISING;
+  RCC_CRSInitStruct.ReloadValue = __HAL_RCC_CRS_RELOADVALUE_CALCULATE(48000000, 1000);
+  RCC_CRSInitStruct.ErrorLimitValue = 34;
+  RCC_CRSInitStruct.HSI48CalibrationValue = 32;
+  HAL_RCCEx_CRSConfig(&RCC_CRSInitStruct);
+
+  /* Select HSI48 as USB clock source */
+  RCC_PeriphCLKInitTypeDef usb_clk = {0 };
+  usb_clk.PeriphClockSelection = RCC_PERIPHCLK_USB;
+  usb_clk.UsbClockSelection = RCC_USBCLKSOURCE_HSI48;
+  HAL_RCCEx_PeriphCLKConfig(&usb_clk);
+
+  /* Peripheral clock enable */
+  __HAL_RCC_USB_CLK_ENABLE();
+}
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* BOARD_H_ */

hw/bsp/stm32h5/boards/stm32h503nucleo/board.mk

@@ -0,0 +1,7 @@
+MCU_VARIANT = stm32h503xx
+
+CFLAGS += \
+	-DSTM32H503xx
+
+# For flash-jlink target
+JLINK_DEVICE = stm32h503rb

hw/bsp/stm32h5/family.c

@@ -67,15 +67,19 @@ void board_init(void) {
   __HAL_RCC_GPIOB_CLK_ENABLE();
   __HAL_RCC_GPIOC_CLK_ENABLE();
   __HAL_RCC_GPIOD_CLK_ENABLE();
-  __HAL_RCC_GPIOE_CLK_ENABLE();
-  __HAL_RCC_GPIOG_CLK_ENABLE();
   __HAL_RCC_GPIOH_CLK_ENABLE();
-  __HAL_RCC_GPIOI_CLK_ENABLE();
 
-  //__HAL_RCC_SYSCFG_CLK_ENABLE();
-  //__HAL_RCC_PWR_CLK_ENABLE();
+  #ifdef __HAL_RCC_GPIOE_CLK_ENABLE
+  __HAL_RCC_GPIOE_CLK_ENABLE();
+  #endif
+  #ifdef __HAL_RCC_GPIOG_CLK_ENABLE
+  __HAL_RCC_GPIOE_CLK_ENABLE();
+  #endif
+  #ifdef __HAL_RCC_GPIOI_CLK_ENABLE
+  __HAL_RCC_GPIOE_CLK_ENABLE();
+  #endif
 
-      UART_CLK_EN();
+  UART_CLK_EN();
 
   #if CFG_TUSB_OS == OPT_OS_NONE
   // 1ms tick timer
@@ -141,7 +145,9 @@ void board_init(void) {
   __HAL_RCC_USB_CLK_ENABLE();
 
   /* Enable VDDUSB */
+  #if defined (PWR_USBSCR_USB33DEN)
   HAL_PWREx_EnableVddUSB();
+  #endif
 }
 
 //--------------------------------------------------------------------+

src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h

@@ -115,6 +115,11 @@
 #elif CFG_TUSB_MCU == OPT_MCU_STM32H5
   #include "stm32h5xx.h"
   #define FSDEV_BUS_32BIT
+
+  #if !defined(USB_DRD_BASE) && defined(USB_DRD_FS_BASE)
+  #define USB_DRD_BASE USB_DRD_FS_BASE
+  #endif
+
   #define FSDEV_PMA_SIZE (2048u)
   #undef USB_PMAADDR
   #define USB_PMAADDR USB_DRD_PMAADDR