Add STM32 B_5585I-IOT2A board

hw/bsp/stm32u5/boards/b_u585i_iot2a/board.cmake

@@ -0,0 +1,8 @@
+set(MCU_VARIANT stm32u585xx)
+set(JLINK_DEVICE stm32u585zi)
+
+function(update_board TARGET)
+  target_compile_definitions(${TARGET} PUBLIC
+    STM32U585xx
+    )
+endfunction()

hw/bsp/stm32u5/boards/b_u585i_iot2a/board.h

@@ -0,0 +1,112 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2023, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+extern "C"
+{
+#endif
+
+// LED GREEN
+#define LED_PORT GPIOH
+#define LED_PIN GPIO_PIN_7
+#define LED_STATE_ON 0
+
+// BUTTON
+#define BUTTON_PORT GPIOC
+#define BUTTON_PIN GPIO_PIN_13
+#define BUTTON_STATE_ACTIVE 1
+
+// UART Enable for STLink VCOM
+#define UART_DEV USART1
+#define UART_CLK_EN __HAL_RCC_USART1_CLK_ENABLE
+#define UART_GPIO_PORT GPIOA
+#define UART_GPIO_AF GPIO_AF7_USART1
+#define UART_TX_PIN GPIO_PIN_9
+#define UART_RX_PIN GPIO_PIN_10
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+
+static void SystemClock_Config(void) {
+  RCC_OscInitTypeDef RCC_OscInitStruct = { 0 };
+  RCC_ClkInitTypeDef RCC_ClkInitStruct = { 0 };
+  RCC_PeriphCLKInitTypeDef PeriphClkInit = { 0 };
+
+  /* Enable Power Clock */
+  __HAL_RCC_PWR_CLK_ENABLE();
+
+  /** Configure the main internal regulator output voltage
+   */
+  HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+  /** Initializes the CPU, AHB and APB buses clocks
+  */
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48 | RCC_OSCILLATORTYPE_HSI;
+  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+  RCC_OscInitStruct.HSI48State = RCC_HSI48_ON;
+  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+  RCC_OscInitStruct.PLL.PLLMBOOST = RCC_PLLMBOOST_DIV1;
+  RCC_OscInitStruct.PLL.PLLM = 1;
+  RCC_OscInitStruct.PLL.PLLN = 10;
+  RCC_OscInitStruct.PLL.PLLP = 2;
+  RCC_OscInitStruct.PLL.PLLQ = 2;
+  RCC_OscInitStruct.PLL.PLLR = 1;
+  RCC_OscInitStruct.PLL.PLLRGE = RCC_PLLVCIRANGE_1;
+  RCC_OscInitStruct.PLL.PLLFRACN = 0;
+  HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+  PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
+  PeriphClkInit.IclkClockSelection = RCC_CLK48CLKSOURCE_HSI48;
+
+  HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
+
+  /** Initializes the CPU, AHB and APB buses clocks
+   */
+  RCC_ClkInitStruct.ClockType =
+      RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_PCLK3;
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+  RCC_ClkInitStruct.APB3CLKDivider = RCC_HCLK_DIV1;
+
+  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4);
+}
+
+static void SystemPower_Config(void) {
+}
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* BOARD_H_ */

hw/bsp/stm32u5/boards/b_u585i_iot2a/board.mk

@@ -0,0 +1,11 @@
+CFLAGS += \
+  -DSTM32U585xx \
+
+# All source paths should be relative to the top level.
+LD_FILE = ${FAMILY_PATH}/linker/STM32U575xx_FLASH.ld
+
+SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32u575xx.s
+
+MCU_VARIANT = stm32u585xx
+# For flash-jlink target
+JLINK_DEVICE = stm32u585zi