A ReAgnus MegaAChip PCB that takes a Gowin FPGA with embedded PSRAM, a PLCC-84 plug and FET level shifters.
THIS IS WORK IN PROGRESS, HARDWARE IS VERIFIED WORKING. FIRMWARE YET TO BE DEVELOPED. BUILD AT YOUR OWN RISK.
For hi-res pics goto the hi-res folder in pics https://github.com/jbilander/ReAgnus-MegAChip/tree/main/pics/hi-res
| Designator | Name/Value | Package | Notes |
|---|---|---|---|
| U1 | Gowin FPGA GW1NR-UV9LQ144PC6/I5 | LQFP-144 | FPGA - Field Programmable Gate Array, 8640 LE, 121 I/O, Embedded 64Mbit 16-bit PSRAM GW1NR-UV9LQ144PC6/I5 |
| U2 | Voltage Regulator 3.3V, LM1117-3.3 or AMS1117-3.3 |
SOT-223 | 3.3V 1A Low Drop-Out (LDO) Voltage regulator. https://www.aliexpress.com/item/32869037691.html |
| U3 | Voltage Regulator 4.3V, TPS73643DBVR or ABLIC S-1132B43-M5T1U |
SOT-23-5 | 4.3V LDO Voltage Regulator TPS73643DBVR S-1132B43-M5T1U |
| U4,U5,U6,U7 | Digital Bus Switch ICs 20-Bit FET, SN74CBT16210CDGVR | TVSOP-48 | FET Level-shifter SN74CBT16210CDGVR |
| U8 | 74LVC1G07 Single Buffer With Open-Drain Output | SOT-353, SC-70-5 | 74LVC1G07 |
| U9 | X-tal driver 74LVC1GX04 | TSOP-6 1.65x3.05mm P0.95mm | 74LVC1GX04 |
| U10 | Bus Transceiver 74LVC245APW,118 | TSSOP-20 | 74LVC245APW-T |
| U11 | Voltage Regulator 1.8V, MCP1702T-1802E/CB |
SOT-23 | 1.8V Low Drop-Out (LDO) Voltage regulator. MCP1702T1802E-CB |
| U12 | Winslow PLCC-84 Plug | PLCC-84 Plug | Optionally homemade plug |
| U13 | PLCC-84_TH_pin_holes | Agnus_TH_plug_pins | Pins to use with homemade plug, 1.27mm pitch Long Pin 1x40P or 1x50P Aliexpress Cut to length after soldering. |
| Y1 | 18pF Crystal 28.6363 MHz (NTSC) or 28.375 MHz (PAL) | 3.2 mm x 2.5 mm | ECS-286.3-18-33-JEM-TR (NTSC) ABM8-28.375MHZ-B2-T (PAL) |
| R1 | Resistor 1k Ω | 0603 | Resistor in optional Oscillator-circuit |
| R2 | Resistor 2.2M Ω | 0603 | Resistor in optional Oscillator-circuit |
| R3 | Resistor 33 Ω | 0603 | Series resistor for CLK from U9 to avoid reflections (in optional Oscillator-circuit). |
| R4 | Resistor 10k Ω | 0603 | Pull-up resistor for pin 41 (PAL/NTSC-selector for A500 Rev.6A/A2000/A3000-pinout) since A500 Rev.6A doesn't have pull-up on motherboard like A2000/A3000/A3000T have. Only needed for A500 Rev.6A. but doesn't hurt to populate anyway. |
| R5 | Resistor 4.7k Ω | 0603 | Pull-down resistor for TCK in JTAG. |
| RN1 | 4.7k or 10k Ω RES ARRAY 4 Resistors | 1206 | CAY16-4701F4LF or CAY16-103J4LF |
| RN2 | 4.7k (CAY16-4701F4LF) RES ARRAY 4 Resistors | 1206 | CAY16-4701F4LF |
| C1 | Capacitor Radial Polarized 100uF | 2.5mm pitch, Through-Hole | ECE-A0JKA101I |
| C2-C4 | Capacitor 10uF | 1206 | |
| C5 | Capacitor 1uF | 0805 | |
| C6 | Capacitor 10uF | 0805 | |
| C9 | Capacitor 1uF | 0805 | |
| C7,C8,C10-C16 | Capacitor 0.1uF = 100nF | 0805 | |
| C17-C19 | Capacitor 0.01uF = 10nF | 0805 (or 0603) | |
| C20 | Capacitor 0.1uF = 100nF | 0603 | Decoupling cap for U8 |
| C21-C24 | Capacitor 0.1uF = 100nF | 0603 | Decoupling caps for U4-U7 |
| C25 | Capacitor 0.1uF = 100nF | 0603 | Optional cap for U3, NR (Noise Reduction) pin 4 on TPS73643DBVR, this pin is NC on ABLIC S-1200B43-M5T1U |
| C26 | Capacitor 0.01uF = 10nF | 0603 | |
| C27-C28 | Capacitor 0.1uF = 100nF | 0603 | |
| C29-C30 | Multilayer Ceramic Capacitors MLCC - 32pF | 0603 | 06031A320FAT2A Caps for optional oscillator circuit |
| L1 | (Ferrite Bead 600ohms 100MHz .5A Monolithic) or 0 Ω resistor | 0805 | HZ0805E601R-10 or 0 Ω resistor |
| J1 | VCC/GND Power Header Male | TH 1 x 2 Pin, 2.54mm pitch | For external power supply to allow programming of device when not plugged into the Amiga socket. |
| J2 | JTAG Pin Header Male | TH 2 x 5 Pin, 2.54mm pitch | |
| J3 | A20-A23 Pin Header Male | TH 2 x 2 Pin, 2.00mm pitch | Input Address lines for jumper-wires A20-A23 |
| J4 | GND MountingHole_2.2mm_M2_Pad_Via | nut and bolt M2 size | for solid grounding via a ring lug connector and a thick jumper wire to Motherboard |
Select one of the crystals 28.375 MHz (PAL) or 28.6363 MHz for the optional onboard oscillator circuit. Probably you want to select PAL/NTSC opposite to what your CLK on motherboard has, this in order to be able to switch between native PAL/NTSC with only a JP-setting on the MegaChip board.
