First commit (culfw 1.6.6)

CHANGED

@@ -0,0 +1,335 @@
+Version 1.66 (2015-11-29)
+- CULV3/V4: add ZWave receive
+- ZWave: receive+send @ 40k, 100k
+- intertechno: modify interval
+- Cw: Write CC1101 register directly
+- ZWave: receive+send(?) @ 9600
+- ZWave: no ack for routed packages (work in progress)
+- RFR: do not report FHT if T01 is zero and RFR target is on (Forum #50756)
+
+Version 1.65 (2015-05-14)
+- CULV3: add belfox (Forum #36810)
+
+Version 1.64 (2015-04-30)
+- CUN*: retransmit patches from doubh (Forum #36529)
+- CUL: due to mem space issues: disabled by default: RF_RWE / MBUS_TX
+- added RF-Native Mode for RFM12 based protocols i.e. LaCrosse/IT+/PCA302,
+  ie.  use "Nr1" 
+- add Bff to test the watchdog (Forum #36215)
+- CUNO2: added SOMFY RTS support to board definition (thdankert)
+- completed wireless m-bus RX/TX support (for T or S mode)
+- IT fixes from bjoern
+
+Version 1.63 (2015-02-08)
+- IT changes from bjoern
+
+Version 1.62 (2014-11-25)
+- Compiling with avr-gcc 4.8.1 instead of 4.3.3 (3.5% smaller code)
+- Clock patches from Ansgar (Forum #24436, reworked)
+- SOMFY_RTS: return already decrypted data when sending commands
+- WMBUS: integration into SCC, CSM, CCD devices
+- HAS_FHT80_TF by Matcher (Forum #29677)
+
+Version 1.61 (2014-06-28)
+- Fix asksin "garbage" message, after X00 followed by X21 (fhem restart)
+
+Version 1.60 (2014-06-22)
+- RX/TX switch bugfix (saves 2ms when switching)
+
+Version 1.59 (2014-06-15)
+- added display_hex8 function in display.h/.c. Is compiled with #define
+  HAS_DISPLAY_32BIT_HEX8. by noansi
+- added cc1101 PLL lock check functions and task, see cc1101_pllcheck.h/.c.
+  by noansi
+- added receiving support of wireless m-bus (T or S mode)
+- SOMFY/Simu send routines by thdankert
+- rpiaddon: initial version for Raspberry PI addon board by Damian Melson
+- SCC: inital addition of new RPi extension
+- UNIROLL send routines (currently CUL only) by C_Herrmann
+
+Version 1.58 (2014-03-14)
+- CUNO2: support for KWL EC 200/300/500 Helios Lueftungen (HAS_HELIOS) via
+  RS485
+- !CUL: extended command for reading unique eeprom values provided by Dudette
+  bootloader. (RM: MAC addr / RP: 128bit RSA private key)
+- all: added sending support for "Kxxxx" messages (requires RAWSEND enabled)
+- all: IT & REVOLT receive support from mehf (disabled per default)
+- all: add AskSin-support for OTA firmware-update
+
+Version 1.57 (2013-07-02)
+- all: wait for CCA before sending in AskSin-mode
+
+Version 1.56 (2013-06-27)
+- improved communications-reliability in AskSin-mode
+- changed first FHT timeout
+
+Version 1.55 (2013-05-21)
+- AskSin burst support (by Michael)
+
+Version 1.54 (2013-04-08)
+- MORITZ: Add auto-ack for SetTemperature
+
+Version 1.52 (2013-01-11)
+- MORITZ: Add support for auto-Ack
+
+Version 1.51 (2013-01-04)
+- CUNO2: added HM485 support (mutually exclusive with DMX)
+
+Version 1.50 (2012-29-12)
+- CUL: add CUL_V2_MAX variant
+- all: sending intertechno/FS20 commands from moritz mode restores moritz
+  mode afterwards
+- CUNO2: added support for DMX on RS485 port
+- some more program cleanup to compile with  avr-gcc 4.6.2
+
+Version 1.49
+- Raw-Mode (G) Send 1-bit optional, to enable sending LOTT Uniroll
+
+Version 1.48
+- CUNO2: added support for hardware patch - connecting Volkszaehler IR-head
+- CUL: added RWE SH protocol receive
+- CUL: added MORITZ protocol receive and send
+
+Version 1.47
+- all: CUL_FHTTK bugfix, don't filter out FHTTK's with a special adress
+       (third byte is one of 4B, 53, 54, 69, 7D, 7E). Workaround: X61
+
+Version 1.46 (2012-07-22)
+- all: CUL_FHTTK is working again
+- all: RFR silence while FHT is active changed
+- all: RFR is compressing multiple FHT messages. Needs current fhem/CUL_RFR.pm
+
+Version 1.45 (2012-07-11)
+- CU*: added support for new multifrequency hardware detection
+- CUNO2: bugfixed FHT8v timing
+- CUL: VH returns the hardware version for CUL_V3 and CUL_V4.
+- CSM: serial line overflow bug, TuxRadio2/board.h parameters changed
+- all: Min length for FS20(4) and FHT(5) set, FHT8v removed from CUL_V2
+- all: RFR won't send while FHT communication is active, T0200 added
+
+Version 1.44 (2011-11-10)
+- CUNO2:new device directory
+- all:  source moved to sourceforge
+- all:  modified InterTechno Support. Now it's possible to send IT from all 
+        RF-Modes with soft-tuning (except CUL_V2)
+
+Version 1.43 (2011-06-25)
+- all:  FS20 repeater support.
+- all:  TX2/TX3 support
+
+Version 1.42 (2011-03-08)
+- CUL:  Version 4 port. Note: you need a current dfu-programmer to flash it.
+
+Version 1.41 (2011-01-27)
+- CUNO: InterTechno(R) Protocol for sending IT-Datagrams, 433MHz 
+- CUL:  InterTechno(R) Protocol for sending IT-Datagrams, 433MHz CUL_V3.hex 
+
+Version 1.40 (2010-11-11)
+- CUNO: OneWire support
+- CUL:  CUL_V2_HM.hex vor the CULV1/V2 devices
+
+Version 1.39 (2010-06-27)
+- CU*: ESA2000 rx support (CULV3 only)
+- CUL: small rfr tweaks.
+
+Version 1.38 (2010-05-23)
+- CU*: EM message send support (CULV3 only)
+- CU*: basic AskSin receive, send and dump support (CULV3 only)
+- CU*: 8v handling rewrite (alexanders model for fast update in multiple rooms)
+
+Version 1.37 (2010-04-17)
+- CUL: size optimizations partly reversed (RFR was not working!)
+- CUL: V3 support
+- CUL: RFR_SHADOW (==bigger in/out buffers for CUL_V2)
+- CUL: RFR: separating data with ;
+- CUL: makefile rewrite to support V2 and V3.
+
+Version 1.36 (2010-01-15)
+- CUL: size optimizations (compiler flags + fht80b_minute)
+- CUL: firmware with RFR/80b/8v, without RFR debug/statistics
+
+Version 1.35 (2009-11-28)
+- CU*: RF_ROUTER fixes (send-bug, timout calibration, PROTO headerbyte added)
+- CUL: Second configuration (make conf2) with FHT8v and without RF_ROUTER
+
+Version 1.34 (2009-11-22)
+- CU*: RF_ROUTER fixes (+ source id added to the packet)
+
+Version 1.33 (2009-11-21)
+- CUN: EXTMEM fixed
+- CUN: temperature disabled as it is too inaccurate.
+- CUN: reading/writing files over ethernet fixed.
+- CUR: reenabled USB after wakeup (myusb/lufa change?)
+- CU*: RF_ROUTER seems to work.
+
+Version 1.32 (2009-11-01)
+- CUN: rebooting (B01 & B00) fixed
+- CUN: generate the same MAC address across updates
+- CUN: temperature reading (first steps).
+
+Version 1.31 (2009-10-30)
+- CUN: Answer commands only to "originator" (USB/TCP). "r" to TCP/IP
+- CU*: booting after eeprom_init fixed
+- CU*: FHT sync from Andreas
+- CU*: changed ringbuffer to fixed size
+
+Version 1.30 (2009-10-23)
+- CU*: FHT8v support.
+- CU*: uptime (t) command is reporting in hex (to reduce code usage)
+- CU*: fastrf fixed
+- CU*: rf_routing  (first steps)
+- CU*: CLOSE_IN_RX deleted. Caused problems with close FHT's :/
+- CU*: T04 (setting sec offset for FHT time) is gone, see the README.
+- README updated.
+- CUN/CUR: Logging must be explicitly enabled with "w01", see the README
+
+Version 1.29 (2009-09-08)
+- CUN: NTP added, enc28j60 auto-reset algorithm changed
+- CUN: logging usig NTP enabled
+- CU*: new fastrf configuration
+- CU*: S300 checksum second nibble
+
+Version 1.28 (2009-08-23)
+- directory reorganization, adding avr-uip
+- MyUSB (aka lufa) update. 2 Makefiles per project for MyUSB and lufa
+- CU*: sending immediately after receiving fixed (problems in fhem notify)
+- CUN: "unique" MAC adress, IP/MAC configured via eeprom (see the README)
+- CUN: DHCP added. RX/TX Led blinks till an adress via DHCP is received
+
+Version 1.27 (2009-08-12)
+- CU*: fht interface rewrite (FHZ "mode")
+- CU*: rf fine-tuning for better FHT reception
+- CU*: command table moved into pgm memory to free up RAM.
+- CU*: CLOSE_IN_RX added (see cc1101 doc)
+
+Version 1.26 (2009-08-01)
+- CU*: FHT80b resend
+- CU*: split transceiver.c in rf_send.c and rf_receive.c
+- CU*: experimenting with fast CC1101 based packet transmission
+
+Version 1.25 (2009-07-25)
+- CUR: Brightness added for V3
+- CUR: fs_sync on reboot
+- CUR: if battery goes below 10% sync the fs and stop logging
+- CUR: battery command for the CURV3
+- CUR: REP_LCDMON (on-screen RF monitor) 
+- CUL: No more power down for X00, go to idle first for wakeup on CUR
+
+Version 1.24 (2009-07-03)
+- CUR: Fixed it to work again on both V3 & V2 CUR
+
+Version 1.23 (2009-06-27)
+- CU*: Version string (USB & V) changed for the CUL433
+
+Version 1.22 (2009-06-26)
+- CU*: HMS support
+- CUR: V3 board support
+
+Version 1.21  (2009-06-02)
+- CU*: FHT protocol filtering flag (X64)
+- CUL: CUL 433 initialization
+
+Version 1.20 (2009-06-01)
+- CU*: FHT buffers moved from EEPROM to RAM, with better buffer usage
+       There are 2 memory models, the default is more RAM efficient but needs
+       ca 200bytes more of program memory.
+
+Version 1.19 (2009-05-30)
+- CUR: menu wraparound
+- CU*: FHT80b communication (no resend yet). TODO: FHT time sync
+- CUL: bugfix: jumping to bootloader works now.
+
+Version 1.18 (2008-04-20)
+- CUL: former bugfix got lost in Check-In procedure
+
+Version 1.17 (2008-04-19)
+- CUR: battery "line" calibrated
+- CUR: enable radio correctly after wakeup
+- CUL: bugfix: EE_LED wrapped on CUL to 0x2, overwriting CC1100 config
+
+Version 1.16 (2008-03-17)
+- CUR: syslog (with logrotate)
+- qfs: fs_rename, fs_read bugfix
+- CUR: "more" (file viewing)
+- CUR: display internally selectable (log/USB/LCD)
+- CUR: reading files longer than 2 sec does not triggers the watchdog
+- CUR: menu "last selected item" is kept in the RAM instead of EEPROM
+- fromhex() fixed: it now only ignores ' ' instead of all non-hex characters
+- CUR: added picture loading from file (P)
+- CUR: builtin logo replaced with a loadable one (each menu can have one)
+- CUR: battery calibrated (get the original values with a01)
+
+Version 1.13 (2009-01-02)
+- Fixed sending longer FS20 messages (for CUR/CUL communication)
+- CUR: Status request from fhem:00_CUL.pm for FS20/FHT/EM/S300 devices
+
+Version 1.12 (2008-12-28)
+- further fht experiments
+
+Version 1.11 (2008-12-22)
+- sending should work now
+- first fht experiments
+
+Version 1.11
+- CUR: Control menu reorganized
+- CUR: Display "stdout" on the title
+- CUR: dpy off if connected to usb (real sleep else)
+- even more pa tables
+
+Version 1.10 (2008-12-11)
+- CUR: RTC
+
+Version 1.09 (2008-12-10)
+- multiple PA tables: x02
+- reboot command changed (B00/B01 vs. b/B)
+- init cc1101 when sending before receive 
+- factory reset changed. Function call instead of writing a magic eeprom byte
+- eeprom magic and version number: all eeprom adresses changed
+- CUR: set X00 for file operations
+- CUR: battery: display red line if not on USB
+- "Upgrade" to 1.5.3: no files changed -> no difference
+
+Version 1.08 (2008-11-12)
+- cc1100.c: sending works again (reset to factory!)
+- CUR: command feedback in the menu
+- CVS tag CUL_VER_108
+
+Version 1.07 (2008-11-08)
+- cc1100.c: abort ccTX / ccRX if 255 tries did not worked.
+- CUR: 5-fold speedup in display data transfer using HW SPI
+- CUR: display battery state on the lcd
+- CUR: LED is inverse
+- CUR: Add some color to the menus
+- CUR: Intro logo
+
+Version 1.06 (2008-11-02)
+- CUR: menu implementation
+- CUR: joystick support
+- CVS tag CUL_VER_106
+
+Version 1.05 (2008-10-26)
+- USB output routines more stable now.
+- CUR: display routine (command d), with antialiased fonts, scrolling
+- CUR: battery check (command a)
+- CUR: Filesystem: qfs. Command r/w to read/write files. tools/cur_file.pl
+- CVS tag CUL_VER_105
+
+Version 1.04 (2008-10-12)
+- l command added (CUL/CUR)
+- L / s command (CUR). Note, s is experimental and will go away.
+- Accepting half-byte S300 messages
+- various small fixes
+- MyUSB update
+- r command (sending raw data)
+
+Version 1.03
+- File reorganization to accomodate CUR and other projects
+
+Version 1.02
+- Version string will be updated manually
+- R/W can take one or two bytes as address.
+- Factory reset byte moved to 0x1FF
+- PATABLE changed to transmit "louder" (+10dB, no PA ramping)
+- Recalibrating every 2 minutes (busy for 1ms, less than 0.01%)
+- Factory defaults chenged to measured optimum.
+

Devices/AirLinked/PWMBOX/board.h

@@ -0,0 +1,46 @@
+#ifndef DEVICE_H
+#define DEVICE_H
+
+#include "../board.h.zCSM"
+
+#define XADB2001
+#define HAS_PRIVATE_CHANNEL
+#define XLED
+
+#define REPTIME                 20 
+
+#undef LED_DDR
+#undef LED_PORT
+#undef LED_PIN
+
+#ifdef ADB2001
+
+#define LED_DDR                 DDRC
+#define LED_PORT                PORTC
+#define LED_PIN                 0
+#define LED_INV
+
+#define KEY_DDR                 DDRD
+#define KEY_PORT                PORTD
+#define KEY_PIN                 3
+#define KEY_IN                  PIND
+
+#define REL_DDR                 DDRC
+#define REL_PORT                PORTC
+#define REL_PIN                 1
+
+#else
+
+#define LED_DDR                 DDRC
+#define LED_PORT                PORTC
+#define LED_PIN                 4
+
+#define KEY_DDR                 DDRC
+#define KEY_PORT                PORTC
+#define KEY_PIN                 3
+#define KEY_IN                  PINC
+
+#endif
+
+#endif
+