ubaboot v0.5 atmega32u4 bootloader

ubaboot v0.5 is a USB bootloader for atmega32u4 in 512 bytes.

Overview

• Targets atmega32u4-based boards
• Compiles to less than 512 bytes
• Tested with Adafruit Feather 32u4 and Teensy 2.0
• Can write and read (verify) both flash and eeprom memory
• Also reads signature/lock/fuse bytes
• Sample pyusb driver program included
• Works with Linux; other platforms may work but not tested

ubaboot uses a custom (vendor-defined) USB protocol. See below for details.

The included ubaboot.py driver program can upload and verify firmware.

Getting started

You must configure ubaboot to work with your board. See config.h.

1. Install dependencies:
   • avr-gcc
   • avr-libc
   • make
   • avrdude
   • pyusb
2. Edit config.h to set required and optional configuration.
3. Build via make.
4. Set your fuses for a 512 byte bootloader.
5. Program your board via "make program". This uses avrdude to flash the firmware; set AVRDUDE_PROGRAMMER in the Makefile for your programmer.
6. Install a udev rule so you can use your device without root privilege.
7. Use ubaboot.py to load programs via the bootloader.

Configuration overview

Required configuration:

• Set crystal/oscillator frequency for your board.
• Set low-speed mode if using the internal RC oscillator.
• Enable USB voltage regulator if needed for your board.

Optional configuration:

• Setup registers and pin number for blinky USB activity LED.
• Customize vendor and product ID.

Protocol details

All operations are control transfers type vendor and recipient device.

Read Signature

Returns the three device signature bytes.

SETUP field	Value
bmRequestType	0xc0
bRequest	1
wValue	ignored
wIndex	ignored
wLength	3

Read Flash

Reads program flash memory.

SETUP field	Value
bmRequestType	0xc0
bRequest	2
wValue	address to read
wIndex	ignored
wLength	length to read

Address and length need not be aligned to flash pages.

Write Flash

Writes program memory.

SETUP field	Value
bmRequestType	0x40
bRequest	3
wValue	address to write
wIndex	ignored
wLength	length to write

Both address and length must be aligned to page boundary (128 bytes for atmega32u4).

Allow 20 ms timeout per page being programmed.

Reboot

Reboots into the target program.

SETUP field	Value
bmRequestType	0x40
bRequest	4
wValue	ignored
wIndex	ignored
wLength	0

Read EEPROM

Reads EEPROM memory.

SETUP field	Value
bmRequestType	0xc0
bRequest	5
wValue	address to read
wIndex	ignored
wLength	length to read

Write EEPROM

Writes EEPROM memory.

SETUP field	Value
bmRequestType	0x40
bRequest	6
wValue	address to write
wIndex	ignored
wLength	length to write

Allow 10 ms timeout per byte being programmed.

Read Fuse/Lock Bytes

Reads the fuse bytes and lock byte.

SETUP field	Value
bmRequestType	0xc0
bRequest	7
wValue	ignored
wIndex	ignored
wLength	4

The bytes are returned in the following order:

Offset	Value
0	low fuse
1	lock byte
2	extended fuse
3	high fuse

Notes

The firmware allows max 64 kib transfers but your USB stack might not.

libusb on linux is limited to 4 kib per control transfer.

USB vendor/product ID 1d50:611c is assigned to ubaboot by openmoko and configured by default. You can use this ID in your projects, or customize if desired.

Thanks

Thank you Richard Woodbury for reviewing lots of code and testing!

Copyright notice

Copyright 2017 by Robert Evans ([email protected])

ubaboot is licensed under the terms of GPLv3. See LICENSE for details.

This documentation is licensed under the terms of CC BY-SA 4.0